Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS869316
This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I searched the internet and found a detailed instructions list (with pics). The written instructions on Partselect.com were on the money but the pics really helped! Start to finish, the entire job took 15 minutes. If you're the least bit handy, this is an easy one!
Help other customers find the most helpful instructions.
Were these instructions helpful?
The first maker I received was broken. The funnel at the top that directs the water into the tray was broken. I called PartSelect and told them how I had received the part and there was no problem. They shipped me a new part, and it must have been the same day as I got the replacement two days later. I was very satisfied with that quick response. I removed one screw and the cover to the wiring harness. Slid the icemaker forward and unplugged the wiring. Then removed the icemaker. I had to remove the old bracket from the assembly as the new maker did not come with one. Installed three screws in bottom of bracket then reinstalled the assembly and plugged the wiring back in. The whole process took about 10 to 12 minutes, very easy.
To get me thinking. . . Our thermostate was not working. . . It was under warrant. . Call repairman. . He came out. . Looked at it, went to supplier got a new one . . . Unplugged old thermostate and plugged in new one. . . . Charge. . . $120. 00 So when the ice maker went out I checked and it was out of warranty. . . Took off door to unit. . 2 Screws. . . Unplugged unit. . . . Ice maked is on a shelf that has notches. . . Lift up a little and slide out. . . Ordered new uniy from partselect. Attanched to shelf. . . Plugged in to electricy and installed shelf. . Prayed a lot and works . . . . Al wilson
Basically, we unscrewed the holding tray and disconnected the water supply and slid the old unit out.We then reversed procedure installing the new unit and poured some water into resevoir and waited till the ice was frozen and then reheated by the bottom section whiched allowed the tynes to cut and dump the cubes. we had previously bought and installed the motor for the old unit but after a day with no action, we brought that unit back to Sears and we ordered the whole replacement unit from PartsSelect. The part came within 3 days and we very happy with the results.
I wanted to make sure I ordered the correct icemaker, so I turned off the water to the icemaker, and turned off the icemaker switch. One screw taken out for the harness protector and the entire unit became loose, and I worked it out of the holding slot and used a really small screwdriver to separate the plug. Once the size was accurately determined, a new unit was ordered. The new unit arrived two days later and the procedure reversed itself. Twenty minutes later "I have ice" Been working well ever since
Removed the plastic service door, exposing the ice maker. Pulled the ice maker and the plastic tray it is attached to out of the freezer. Then unplugged the electrical connectioppn, which alllowed me to remove the ice maker and the plastic tray. I then used a 1/4" driver to remove 3 screws holding the ice maker to the tray and one screw that held a plastic cover over the electrical connection. Installation was everything in reverse of removal. Take care to install the water hose into the ice maker. Ice maker started working immediately.
Ordered a replacement which arrived quickly, and delivered the next day. It was not difficult, three screws to undo and one electrical connection.
refridg only 7 years old, poor design by whirlpool as this is second time ice maker failed. install was easy, hardest part was figuring out how to remove old unit. saved more than 50% of cost by doing it myself this time.
Bless you PartSelect. Easy fix,saved Dollars. Great website. The satisfaction of fixing it myself was worth $. It is not the first time you have helped. PLEASE keep up the good work.
Took out 5 screws and replaced the unit easy as can be.
After troubleshooting to determine that I needed the Icemaker assembly, I ordered the parts early on a tuesday and they arrived the next day. Quick. Opened the box and there was no packing material, just the icemaker in the box with a slip of paper instructions with one sentence on it. Said to remove ice shield from old icemaker and install on new one. To remove the old icemaker, I first had to removing the one screw on the bottom that secured the cover over the wiring harness. Next I removed the cover by sliding it towards back of freezer section and guiding around wires. Next I depressed up on two spring clips on the bottom of the icemaker to release it from the tracks and slide the icemaker out. Be careful with the hose for the water outlet. You may have to tip it backwards to get it to clear. Once out of the tracks, I disconnected the wiring harness and removed old icemaker. I reversed the process to stall the new one after I had removed the three screws and the ice shield off the old icemaker and installed on the new one. After installation, it took about 10 minutes for the sound of water running into the trays and we had ice 30 minutes later. Worked fine and hasn't missed a beat yet.
I just followed the instructions that other people had posted on your site. That informations was extrememly helpful and was part of the reason I chose Parts Select. That and the fact that you had multiple pictures of the icemaker which meant I knew I was ordering the right part. You are the best product/info site I have experienced to date. THANK YOU!
Removed old unit and installed new unit. It was quick and easy.
Pulled the old one out and replaced it with a new one.Very Simple.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.