Spark Module

PartSelect Number PS8691157

This is a 4-point re-ignition spark module. NOTE: This part has been redesigned by the manufacture, it may appear different but will still function the same.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $205.00
  • You Save

    $34.17
  • Your Price

    $170.83
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 5 reviews What's this?
1-5 of 5
 

15 of 24 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Wrench set

CustomerBill from Pearland TX

Would not stop igniting even after fire was on

unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 10 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from Ranchos de Taos NM

Burners kept clicking after ignited

This problem was driving me crazy for months. Of course, after I bought and installed the part and it still was not fixed I finally found a website that told me how to fix the clicking. The problem is that the removable head burners (#8 on the top assembly diagram) are not making good electrical contact with the base burners (#22). What I did was grab the head burners and grind them back and forth into the base burners with the weight on the heal of my hand. Steel wool or sandpaper would work too--you just want to clean the surfaces to restore electrical contact.
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMichael from St Louis MO

One burner would continually keep sparking after burner ignited

Removed the small access cover on the bottom of the cooktop by reaching inside and under the cabinets. Removed the module which was held by two hex head screws, unplugged the wires noting the location and color of the wires. Plugged the wires into the new module in the proper locations as noted previously. Attached the module with two screws, and then attached the cover/access plate with two screws. Problem resolved, repair was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from White Rock NM

The spark igniters would continue to spark after the burners were lit

Since the problem would only occur when the right front burner was on, I first replaced the ignitor, but the problem persisted. To replace the spark module I had to pull the range out of the nook it is in in the counter top. Then (after ensuring that the power was off) I removed the back cover. The spark module was easily located and removing two screws and disconnecting a few wires liberated it. The new one went in easily since it is the same part number and an exact match. Put the back on and check that the problem was solved. Done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 5 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

Customerned from leland MS

Would not light

remove two screws then unplug the wires put the wires back on the new one

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5