Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS8689825
The pump ejects the water from the dishwasher.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
**** A stubby Philips screw driver will save you a lot of headache taking the two retaining screws out that hold the drain pump assembly to the hanging bracket *** An inspection mirror was also helpful trying to locate these screws. I thought the pump impeller vane was possibly broken because the pump would not drain the dishwasher but it would energize and make a loud clicking/rumbling noise.1) Drain water from the dishwasher. I used a piece of tubing and siphoned the water out. Remove front cover plate.2) Turn off breaker and dsconnect two wires going into pump.3) Remove the pump inlet. I kept the 4" rubber jumper piece attached when I took the pump out.4) I had to disconnect the wash water feed line to be able to reach the hose clamp on the pump outlet.5) Loosen hose clamp on the pump outlet if you can reach it, otherwise remove the two screws that hold the drain pump assembly in. There is one screw on each side of the pump. I used an inspection mirror to see the screws. I had to use a stubby Philips head screw driver to take the screws out.6) Wrangle the drain section out and finish taking off the pump outlet hose clamp. Install new pump and work backwards to put it together.When I pulled the pump out I found the impeller to be complete (not broken as I had thought) and I saw it had two small steel balls that sat in grooves. I think the two balls and groove act as a safety detent and disengage the pump if something big gets sucked in. I pushed down on the impeller and everything snapped together nicely. Since I already ordered a new pump and I had everything taken apart already I installed the new one but I think I could have just used the old one.Hope this is helpful to someone else. Washer has worked fine since.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Pulled the dishwasher out and laid it on its back. From under the dishwasher I unscrewed three screws and freed the drain pump from some sort of frame. Then with the pliers loosed the orange clamp that held the black hose to it. Then unscrewed the clamp that held the white hose to it. Then pulled out the purple and white fuse wires. These wires were very tight I used pliers to get them off. The pump was free. Be sure to have a bowl to catch all the water. There wasn't a lot but it stinks. Then put it all together the way I took it apart. The dishwasher works perfectly now.
Old pump impeller (internal to pump/motor part) snapped into place, but snapped out of place after warranty.Disconnected power. Removed bottom spray arm and strainer. Siphoned out remaining water. Removed hoses and two mounting screws on pump. Removed wires. Removed pump.Installed pump in reverse steps.
I already had the dishwasher pulled out (remove the two screws from under the counter holding the dishwasher in place) The drain was located on the right side at the bottom very easily removed after taking out the two screws and removing the tubing. Attached the tubing to the new drain pump, made sure clamps were in place and then screwed the screws back in to hold the drain pump into the bracket. Ran the dishwasher once before pushing it back in to make sure there were no leaks. Had a leak but completely unrelated to the drain pump.....I had to replace the hot water supply line the next day, also SUPER EASY. Pushed dishwasher back in and replaced the two screws into the brackets that hold the dishwasher in. Kind of disappointed that I had to replace these things since the dishwasher is just over a year old, but PartSelect made finding the part super easy and they were by far the BEST PRICE! Thanks again! Only suggestion is I wish that it would have come with directions...but I figured it out pretty well!
I pulled out the internal filter and assorted washer parts. All in good shape. I bailed out the washer and removed the pump assembly from under the washer. I pulled it apart to inspect impeller. all looked fine. Plugged pump in and turned on pump cycle. Pump did not operate as it should have and I ordered new pump. My daughter put it back together and all is working well now!
I ordered the replacement pump from Partselect and it arrived 3 days later. The new pump went in very simply with two mounting screws (don't over tighten!!) and the two hose claps for intake and discharge. It works perfectly!
cleared water from machine with bulb type basting tool. Placed two large bath towels on floor in front of machine. Removed machine to floor laying it on the towels on its left side. Removed pump. Installed new pump. Reinstalled machine. Worked fine.
Removed the screws at the top which held it in , then I pulled it outside of it's shell, took it apart and took the drain part off, replaced with new drain part, put it back together the same way I took it off, pushed it back in, put the screws back in, tested it, and it worked. Ta Daaa!
pulled out dishwasher ,left lines hooked ,started cicle .heard pump.took apart.seen problem. order new one ,works like new..
replaced the pump
The drain motor on the dishwasher started to and eventually did fail. I removed the two screws holding the unit in and the front plate on the bottom. I slowly walked it out from under the counter, and tipped it up on its left side. I removed the two mounting screws, and loosened the hose clamps on the inlet and outlet of the pump. Flushed out the drain line of left over soap and goo the pump failed to clear. Then installed the new one reversing the process.
replaced the motor after fixing the impeller once before. seems to be a weakness in this model based on what I've read here. The motor does not fail it's the little impeller inside the housing that comes apart. One word of advice: use a wet/dry shop vac to extract the standing water from the dishwasher.
I removed the drain hose from the drain pump removed 2 screws then removed smaller drain hose and disconnected 2 wires. The new drain pump was now ready to put in. Very easy job! Customer service made ordering the pump very easy!!!!!
Remove lower front face by removing 2 screws. Turn power off at the breaker. Disconnect the power by removing the power cover screw and cover. This is located on the bottom right of the unit, next undo the wire nuts, and pull out the wires. Next turn off the water supply to the dishwasher. Then using an adjustable wrench disconnect the water line. Be careful it could bend. Once the power and water is removed gently slide out the unit. The pump is located on the right side under the dishwasher. Remove the to screws holding the pump in place. Unless the repair is done outside place a drain pan under the pump to catch any left over water. Next using needle nose pliers squeeze the clamp closest to the drain and pull the hose off. Pull out the pump, squeeze the second clamp, and remove the hose from the pump. Place hose on new pump and the work backwards installing the pump.
removed the old pump and replaced it with a new one
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.