Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS8260227
The gasket provides a waterproof seal between the tub and the door.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
Help other customers find the most helpful instructions.
Were these instructions helpful?
With the door wide open and lower dishtray out, I pulled the old gasket out of its channel. I cleaned the channel with a rag and replaced it with the new gasket. It needed to be trimmed about an inch in order to get the door to close properly. Took me about 5 minutes. Then I removed the old bottom door gasket. Just grasped the plastic edge showing while the door is completely open. Pull outward with fingers moving toward the heating element. Cleaned this area also. Took the new gasket with notch on the right hand side of the dishwasher and pushed it into place. If you get down and look closely, you can see where the notch hooks up. The rest of the piece just slides in after that. Hasn't leaked since! No leaks AND no service call fee. Parts came super fast! So glad I found this website. I'm a housewife, you can do this!
This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in. 1. Removed stops on front end of Upper Dishrack Slide on both sides.2. Removed Upper Dishrack3. Remove Roller and Axle/clip (4 each)4. Push Roller onto Axle on all 4 kits 5. Install all 4 roller kits on Upper Dishrack6. Remove stops from back end of Upper Dishrack Slides.7. Remove both Slides8. Remove 8 each Tub Wheels.9. Using old or new Screws and Washers, install new Tub Wheels.10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.11. Install stops on the back end of Slides.12 Install Upper Dishrackinto slides13. Install front stops on slide14. Pulled out Gasket15. Install replaced Gasket
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.Water leak solved...
1. Bottom door gasket removed very easy by grabbing left corning and pulling out. Starting with notch on right side, slide the hard plastic side up at a slight angle to catch the slot the gasket will seat in. Slowly moving toward the left, push gasket into seated position. Notch in gasket will make sure it is in correct position. Push gasket all the way in so that it is flush with bottom edge of door. Watch when first sliding gasket in, it has to g at a slight up angle or it will fall into an empty space.2. Remove Tub gasket by gripping one side and pulling out. Replace in same fashion making sure the angled wedge of gasket is first part that lays flat in slot. Working from one side to the other, make sure the gasket seats completely. Trim excess if necessary.
Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!
#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays. Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.
Repair was easy. Unfortunately I really didn't need the springs or linkage, but I couldn't see that until I took the dishwasher out from the counter. The springs were not stiff enough to keep the door from just falling open. So I cut about an inch off the long end and bent it into a hook. I didn't need new linkages the old ones were fine. The gasket made the biggest difference and went in very easy. The door will be difficult to close for a few times then everything works great.
If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.
I received the parts 3 working days from order. They were in perfect condition and exactly like the originals.Pulled dishwasher out from under counter. Removed door. Replaced drain hose. Replaced gasket. Replaced springs. Put door back on. Tried rinse cycle. Placed dishwasher back under counter. Works like new.
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.