| |
4 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerThomas from Schwenksville PA
The ice/light buttons were cracked and broken
First of all, I ordered in the afternoon and the part was on my doorstep the very next day, amazing shipping. I shopped all over and this was the best price by a few dollars. I hope I never need any other parts, but if I do, I will come back to buy my parts here.
I pried the old cover off with a pocket knife and carefully installed the new one. Now it looks great and it only took me about 5 minutes.
|
2 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDan from Front Royal VA
Door panel was damaged and the cover over the buttons was torn.
Label cover was glued on and you simply pull it off and replace it with the new one. That takes about 2 minutes! The front panel was dented and all you have to do is pull off the rubber trim on the bottom and replace the panel. The dishwasher looks new!!
thanks
dan
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMark from Winter Springs FL
Label face plate cover over ice selector cracked
I removed the three screws at the bottom of the ice maker dispenser tray and took the entire unit off. I unplugged the electrical connector, removed the damaged module face plate and replaced it with the new one. Put everything back in reverse order.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRandy from Covington GA
Not despensing ice properly, module label cover cracked over buttons in door
Took out old Ice container assembly without any tools and replaces with a new assembly. After that ice despensed properly.
replaced the cracked Module Label Cover with new one. Attached with adhesive as it was previously.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerdaesha from spring hill TN
The label cover on my fridge was broke...
It was very easy to install the new label cover... peel and stick! However, the only problem I have with the part is that it was shipped to me "folded in half." Because the sticker is a hard plastic, it made a crease down the center of the label. I tried to smooth most of it out, but the crease was pretty substantial. I thought about returning it, but I opted not to because it almost looks worse without one on when compared to a creased label. Although it works, technically, I probably will go elsewhere for future products.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerClaude from Las Cruces NM
Refridge label for water ice, light, material hole from use.
Very easy to peel off old label and apply new self adhering label. Looks great ! I have ordered other parts from PartSelect and have been very satisfied. Always the right part the first time !!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerSharon from England AR
Did thomas stainless steel paint on white frig. Needed to replace white drip tray and label
the tray just pulls out, with a little encouragement. then the new one was put in place. the module label just peeled off and i stuck on the new one. new frig looks fabulous. i used krylon for plastic to paint the rest of the housing for the ice/water dispenser. i chose not to paint the water tray as i feared the frequent wasking would wear on the painted part. new frig just looks fabulous !!!
|