Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS815938
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
All I had to do was replace the spring and retainer on the side of the dishwasher which amounted to pulling it out far enough to reach the eyelet that the hook went into and then stretching it to the retainer attached on the other end. I really like partselect, I have done some things in the past and they are very helpful on the site and on the phone and I would recommend them to anyone and I would not normally do that unless it has been an excellent experience.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy.Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak. The dishwasher is running as good as new.I ordered these parts on Friday morning. They were on my door step Monday morning, I highly recommend ordering from this site.
Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.
New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .
Repair was easy. Unfortunately I really didn't need the springs or linkage, but I couldn't see that until I took the dishwasher out from the counter. The springs were not stiff enough to keep the door from just falling open. So I cut about an inch off the long end and bent it into a hook. I didn't need new linkages the old ones were fine. The gasket made the biggest difference and went in very easy. The door will be difficult to close for a few times then everything works great.
I received the parts 3 working days from order. They were in perfect condition and exactly like the originals.Pulled dishwasher out from under counter. Removed door. Replaced drain hose. Replaced gasket. Replaced springs. Put door back on. Tried rinse cycle. Placed dishwasher back under counter. Works like new.
Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.
My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!
I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.
Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.It was pretty straightforward -- no big deal.
I removed the wires from the heating element. I removed the 2 brass nuts that had split down the side. I replaced them with 2 new brass nuts. Tightened with a wrench. I then installed the missing door spring. The repair itself took about 5 minutes.
Replacing the door bottom gasket is a breeze, just grasp with a needle nose pliers and pull out. I positioned a small mirror inside the dishwasher so I could see where the gasket fit back in. I pushed the new gasket into the slot and ----done.The springs require that the dishwasher be pulled out from its opening after removing the screws holding it into the cabinet at the top of the dishwasher. Replacing the springs is easy, just remove the old ones from the the bottom frame holes and the plastic holder and put the new ones on through the plastic holder and then into the frame. Push the dishwasher back into its opening, square it with the cabinet and reinstall the mounting screws.
First remove the kick plate.Then look with a flashlight & mirror to make sure which, the spring and or the Spring Linkage are broken.With the door open, to have less tension on the spring, replace the spring and or the spring linkage.Attach the kick plate
Replaced two springs
We pulled the dishwasher out enough th expose the sides where the springs are attached. We removed the oldsprings and attached the new ones. Then put the dishwasher back in place.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.