Ice Bucket and Auger Assembly

PartSelect Number PS783770

This part holds the ice once it's released from the icemaker. When activated, the auger rotates and pushes ice out of the bin through the chute to the user.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Ice maker not making ice.
  • Noisy.
  • Compare At

    $225.77
  • You Save

    $37.63
  • Your Price

    $188.14
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 17 reviews What's this?
1-15 of 17
 

61 of 71 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerMichael from Matthews NC

Ice maker would not dispense and made a loud clunking sound

First I replaced a cone shaped piece at the rear of the auger. That worked for about 20 minutes and it snapped off the middle. Same as original problem. Then I replaced the whole damn bucket and auger assembly. Works like new. Should have done that 1st and saved $24 and a week.

Help other customers find the most helpful instructions.

Were these instructions helpful?

32 of 37 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerRobert from Kalamazoo MI

Plastic circle rotor at back of ice bucket kept breaking into smaller plastic pieces that mingled with the ice and each time you got ice you had to check for plastic pieces.

Purchased new auger & bucket assembly and just put it into freezer and tossed out the whole defective bucket / auger assembly. It would have been too difficult to just replace the plastic disk / rotor at the back of the ice bucket; also soo expensive if a repair person were involved. Suggestion: make the back disk / rotor plate of more break resistant material, i.e. metal of tougher plastic. Thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 17 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerAlbert from Houston TX

Ice would not feed

Found that the plastic end piece was broken in two where the auger attaches at the rear of the ice tray. Purchased new one and installed. Lasted about 1 day. Purchased the whole assembly and it now works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 16 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerLawrence from Wilmington NC

"plastic" retainer/bushing in rear of ice bucket damaged

Replaced plastic part and it immediately tore up.
Ordered entire assembly, icebucket and auger. Replaced and is working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 14 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDIANNA from POWELL OH

Broken auger assembly

First tried to fix old auger. Bad way to go. Spent $30 in parts and didn't work. Don't mess around. Order this whole thing, slide the old one out and the new one in and you're good to go. I wish I would have done this in the first place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerNeal from Haverhill MA

Old unit was worn out from over use

simply push new ice bucket into position and your done. works better than new! saved 200.00 from calling in a tech for the repair. the part sent is a original GE part not an aftermarket part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerMichael from Mesa AZ

Ice maker auger.Bucket assembly did not dispense ice

removed the old assembly - slipped in the new one - worked great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerGary from Katy TX

Ice would not dispense. Auger made clanking noise.

So easy.Remove. ice bucket, poured ice into replacement .Reinstalld. No tools. 3 minutes to do

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerWayne from Streetman TX

Ice cube guide on auger shaft sheared loose.

Pulled out old bucket asy. and pushed new asy. into position. Hardly worth talking about. More important is that this is a GREAT place to find appliance parts. Shipping is super fast too.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRobert from Weeki Wachee FL

Ice auger broken twice

This is second Ice Bucket Auger I had to replace, don't know why it's breaking , but PartSelect was great to work with, replaced the broken part, was fast and very nice to help. I really appreciated their service. There was no repair, I mean, Open the box, take out broken Auger Box, put in new one. No possibility of error.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customerhoward from new york NY

Replace ice bucket and augur in ice maker of ge refrigerator

the part arrived 1 day EARLY !! fabulous.
It was a perfect fit. Took no tools and only 5 minutes to slide old drawer out, empty cubes into new drawer, slide new drawer into place.

The purchase experience was fabulous.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerWILLIE from CERRITOS CA

Auger was broken

REPLACED THE AUGER

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerGregory from Sierra Vista AZ

Replace ice bucket

Originally replaced the "Ice Dispensing Tray Cup", but after a couple weeks it failed as others have reported. The problem appears to be correct alignment of the auger after replaceing the Cup, the ice crushers appears to be, I guess Not In Alignment" with the unit. Bypass the Cup and order the entire dispenser.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Socket set

CustomerJoseph C from Oklahoma City OK

No water - light dimming - etc.

Moved refrig away from wall and unpluged electric cord. Removed cover from control board. Removed connector plugs from control board. Removed old control board and replaced it with new control. Replaced connectors and cover. Pluged electric cord into wall socket. Operation, OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

  • Ice Bucket and Auger Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDONNELL from PORTSMOUTH VA

Ice make running slow with no ice coming down shoot

got new augerz & bucket asy/ remove old bucket put in new on ice coming out like new refrig

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 17