VALVE

In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

I had two problems, the first was that water was dripping from the through the door outlet and the second problem is that the ice maker wasn't making ice.

Replacing the water valve was a simple process:

1. Turn off the water to the fridge at the household shutoff valve.
2. Move the fridge away from the wall.
3. Unplug the mains power (AC) plug from the wall power outlet.
4. Remove the 5 screws with a nut driver that hold the cardboard backing off the refrigerator.
5. (This is a great time to vacuum off the coils and underside of the fridge.) Disconnect the water supply from household plumbing with a box end wrench or channel lock pliers. I kept a large plastic cup and rag handy for the left over water in these hoses.
6. Remove the two screws from the water valve bracket on the right hand side and pull the water valve straight back from the fridge and line up the new valve in the same orientation.
7. Remove all the color coded electrical connectors (3 of them) and attach them to the new water valve.
8. Remove the remaining water hoses and attach them to the corresponding connectors on the new valve.
9. Dispose of the old valve and reinstall the new valve in reverse order.

The problem with the ice maker not making ice was because water was flowing so slowly from the valve that it was stopping in the fill tube at the back of the freezer and freezing stopping all water flow into the ice maker. I pulled the fill tube out of the back of the freezer from behind by rotating it 45 degrees counter clockwise and pulling straight out removing the ice blockage and drying the fill tube before I reinstalled.

Since I replaced the valve I had to take the cover off of the icemaker and set the water fill level down (screw toward the minus sign) and then adjusted it by checking the ice after each time it dropped and increasing the fill amount by 1 full turn (roughly 0.7 ounces) until it was just enough to make fully formed ice cubes.

This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

Repair was very easy - and to my great delight, they have replaced the old-style compression fittings with PEX push-fittings. You just clip the old compression ring and nut off the tubing and insert the tubing firmly into the fitting. SNAP! VOILA! PEX fittings are the greatest things since sliced bread. I used it to plumb my new house.

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

UNPLUGED THE ITEM. TURNED OFF THE WATER SOURCE. REMOVED THE CARD BOARD COVER. DIS-CONNECTED THE WATER HOSES. UNPLUGED THE CONNETORS. MATCHED UP THE COLORES AND PUT IT BACK TOGETHER, VERY EASY. EVERYTHINGS WAS COLOR CODED.

1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

pulled fridge from wall, removed card board cover, unplug the fridge. turn the water off to the fridge. remove the water source from fridge first then remove 2 screws that hold the valve. then the wire plugs. hoses.. they were color coded.

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

The hardest part was figuring out how the front plate comes off. The tray will come forward when pried with a screwdriver. Then the top will come off but you will have to leave on due to attached wires. After that it was a piece of cake. Unscrew screws (6), remove small plates holding arm in place, remove arm, replace with new actuator, and close things up. As far as the valve, just take your time and, if needed, cut off pointed ends of tubings and push into new valve. Unplug color coded plugs and plug into new valve. Reattach valve to fridge and your done. We started everything up before attaching backing to make sure there were no leaks.

REMOVED THE TWO SCREWS THAT HOLD THE ELEMENT IN PLACE. THEN I PULLED THE ELEMENT OUT ABOUT 3 INCHES AND DISCONNECTED THE WIRES. EVERYTHING MATCHED UP PERFECTLY.

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine