http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/HZVQ2R9M.gif
See part F35 in the diagram

Drain Pump - 60Hz 120v

PartSelect Number PS7783938

Manufacturer Part Number 137221600
Manufactured by Frigidaire

The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Will not drain.
  • Unusual Noise.
  • Leaking water.
  • Pumps but will not spin.
  • Not draining.
  • Compare At

    $119.83
  • You Save

    $19.97
  • Your Price

    $99.86
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 14 reviews What's this?
1-14 of 14
 

74 of 89 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

Customerkenneth from willard OH

Would't spin all water out or rinse out clothes

uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31 of 33 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customersara from North Miami FL

After a full cycle the washer would not drain the water

After reading the possiblilities of problem, I determined that the drain pump was not working; therefore I ordered a new one. When I opened the washer to replace the part, I found out that the pump was working but the filter was stuffed with pieces of rubber that came out from a rug I washed. Once all the stuff was removed, the washer worked just fine. PartSelect was very gracious to accept the returned with not questions asked!! Thanks partSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

23 of 26 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJohn from Mason MI

Pump very noisy, failing.

Disconnect water and electricity.
Shop-vac out the water in the internal drain hose.
Remove back cover, tip washer on side to gain access.
Un-clamp rubber drain hose,unscrew pump and remove.
Cleanout filter cup (yuk!) find coins and hairpins.
Attach drain hose to new pump and re-install with hose clamps from hardware store because spring clamps were impossible (arthritis in fingers).
Reconnect water and electricity.
Test for leaks and tighten clamps if necessary.

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 27 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerWilliam from York Springs PA

Discharge of water out of wash machine

remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 17 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerHarry from Zephyrhills FL

The washer would not drain

After removing the front of the washer, I used slip joint pliers for the hose clamps, then a screwdriver for the mount bolts and replaced the pump motor in reverse order. The pump was ordered on line on a Friday before 10am and was delivered on saturday moring by FedEx. I could not have expected such fast and efficent service!
Great Job!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 19 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLili from Jamestwn NY

Water pump broke

My Husband did the repair it took less than 15 minutes. He popped the front off the washer. He then unscrewed two screws and removed the pump assembly. He popped the new pump in, and put in the tow screws. Then he put the washer front back on replacing two screws. It took all of five minutes. I am so pleased it was so easy. I told him next time I'd do the repair and he could watch!
Lil

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 22 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerBrian from Murfreesboro TN

Tub wouldn't drain

First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, put the hoses on, plug in motor and replace front panel. plug into wall

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 14 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerHarold from Denver NC

Water not draining

It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and move back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 18 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

Customerloudvik from glendale CA

The pump had died

First I removed the two screws that hold the pump in place. I then pulled the pump out and replaced it with the new pump.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJeff from Weyauwega WI

Machine would not spin.

Once I figured out that it would not spin because it did not drain. Unplug machine and remove the back pannel. Locate the drain pump on the bottom of machine. Remove the power wires and the screws holding it to the bottom. Then use a pliers to remove the hose clamps ( was easer for me to tip the machine forward ). Be prepaired to catch or soak up extra water from lines. The hardest part to the install is the limited room you have to work with. Install screws to hold the pump in place then install water lines, power wires and back pannel. Only thing left is to plug it in and watch for leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerMatthew from Weyers Cave VA

Water flooded floor

First I took sides off the washer. I then took screws out of the Drain pump holder. Unclamped the two pipes from it. Undid the wires to then drain pump. Screw in the new pump hardware. Plugged in the wires on side of the pump. Reclamped the pipes. Put sides back on washer and it worked. That easy and took less then 30 minutes. I am no handy man so thats how easty it was.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerSiobhain from Ashland NY

Washing machine wouldn't drain

i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 11 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v
  • Timer

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

Customerbig fred from prospect heights IL

Tub won't drain& timer control won't go to correct setting

To replace the pump remove to lower screws on the front panel,remove panel ,pump is in the front section , remove two screws that attach pump to lower housing.
To replace timer remove screws on the plate that the contrlos on mounted on. Once you have access to timer you must remove the nylon pin in the back of the timer that holds the dial to the timer base.You can not remove the knob without removing the pin

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

  • Drain Pump - 60Hz 120v

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerKEITH from BEND OR

Spin cycle wouldn't work

Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-14 of 14