BBB A-Plus
774065-1-M-Whirlpool-9706529-Worm-Gear.jpg
774065-1-S-Whirlpool-9706529-Worm-Gear.jpg 774065-2-S-Whirlpool-9706529-Worm-Gear.jpg

Worm Gear

PartSelect Number PS774065

Used in Stand Mixers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Touchpad does not respond
In Stock

  • Compare At

    $9.86

  • You Save

    $1.64

  • Your Price

    $8.22
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 NEXT > 16-21 of 21

 

4 of 11 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Wrench(Adjustable)

Customerbarbara from hancock WI

Gears broke

remov5 screws then snap ring thenn 4 screws then reploace with new parts and put back together

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerLinda from Ivanhoe VA

Needed repair

The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJerry from Southport NC

Worm gear stripped.

Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

    • Worm Gear

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

Customerkarl from Eureka MT

Gears were stripped from overload of bread dough

At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

    • Worm Gear

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJoseph from Mentone CA

None

followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

    • Worm Gear

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerKenneth from Brookings OR

Mixer beater quite

disassembled unit gear head and replaced broken part, then reassembled

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 NEXT > 16-21 of 21