774065-1-S-Whirlpool-9706529           -Worm Gear
774065-1-S-Whirlpool-9706529           -Worm Gear 774065-2-S-Whirlpool-9706529           -Worm Gear

Worm Gear

PartSelect Number PS774065

Used in Stand Mixers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Touchpad does not respond.
  • Compare At

    $7.52
  • You Save

    $1.25
  • Your Price

    $6.27
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 21 reviews What's this?
1-15 of 21
 

32 of 33 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerBarry from Rowland Heights CA

Wouldnt turn beaters

removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 25 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDennis from Lake Mills WI

Mixer made very bad grinding noise, and would skip while making bread dough

1, REMOVED TRIM PIECE (1 SCREW)
2, REMOVED COVER (4 SCREWS)
3, REMOVED SPEED SWITCH ASSEMBLY (2
SCREWS)
4, REMOVED GEAR COVER (4 SCREWS)
5, REMOVED AND EXAMINED 2 WORM GEARS FOR WEAR. GEAR COVER WAS BADLY CRACKED, DON"T KNOW IF IT WAS CAUSED BY A PREVIOUS REPAIR OR BY HEAT, AS OLD COVER IS PLASTIC.
RECEIVED NEW PARTS AND INSTALLED THEM,
2 BEARINGS, 2 WORM GEARS, 1 NEW COVER OF DIECAST METAL AND A NEW GASKET.
ALL REPAIRS MADE WITH A #2 PHILLIPS SCREW DRIVER.
MY WIFE THEN MADE BREAD, AND IT PREFORMED FLAWLESSLY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGary from Plano TX

Gears stripped on stand mixer

Bought a KitchenAid Pro Series stand mixer from Sam's Club about five years ago. The transmission gears stripped. It is failry easy to replace but you need to replace the worm gear and the pinion at the same time. Make sure all the old grease is removed completely to ensure no old shavings reaming in the transmission housing. Also, if you have a fiberglass transmission housing, inspect the housing closely to indetify any hairline fractures and do not fill the transmission assembly with too much grease becasue you need room for the housing to breathe when the unit is in operation. If you fill the housing too much and tighten it, it "WILL" crack the housing. You want enough gree to keep the asssemnly lubricated but not too much that when you run the mixer that it expands and cracks the housing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerKen from Spicewood TX

No beater rotation (stops in one place)

Remove the top cover. Loosen the circuit board and remove the gear case. Remove the retaining clip on the gear shaft and remove the gears. Clean the old grease out and relube. reassemble in reverse order . Not a bad job at all.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrederick from New Hartford NY

Worm gear stripped

Removed the lid of the mixer. Cleaned all grease and removed the worm gear. Installed new gear and packed with new grease Installed lid and checked worked perfect. Easy repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 18 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerjoe from monaca PA

Mixer does not mix 4 cups of flour with 6 eggs very easily

sat on the kitchen table and with a screwdriver started to disasemble the mixer,hardest part was taking snap ring off (easy after you buy snap ring pliers)as gears were lifted off noticeable wearing was present on all parts. the bearing housing on the gearcase was broken lose, the only major expense. the other parts are not expensive so i decided to renew all parts. glad i did felt proud of myself when job was done. would do it again Joe

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

Customerandy from hanover PA

Kitchen aide stand mixer - epicurian 6 quart model

after numerous calls to kitchen aide and ka repair centers - i decided that their remedy was to sell me a new or refurbished model -- so i decided to try the repair myself - why not - the appliance didn't function and their fix again was close to the price of a new one --- the fix - remove the band (small screw in back --- 4 screws hold on the top of the mixer - remove them and pull off the top -- the gears are at the front -- four screws hold the top in place- remove them and pull off the cover -- this is where it gets interesting - it's a little messy with the grease -- but clean out as much as possible --
the toughest part is then removing the retaining clip --- (a tool is avail at numerous hardware stores that will make it a bit easier about $20. ) but pry the clip up and slide off top -- remove gear - clean out completely - remove all old grindings -- replace gears -- add grease and reverse order... great fix -- even with purchase of pliers it was cheaper than any offer from kitchen aide....

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerVincent J. from Hudson NY

Worn gears had to be replaced (second time)

the hardest part is removing the retaining ring (didn't buy pliers)after that it is very easy, remove ring, top gear, center pin, bottom gear,worm gear(was removed first)the grease is pretty nasty,clean off the old grease and put it all back the way it came apart,with new grease.And then PRAY !!!!!!! THANK YOU PARTS SELECT for your wonder smart staff.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGary from Hamburg MN

Gears and bearing failure

inspected and replaced worn components

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerStuart from Pittsford NY

Gear stripped was trying to replace

Could not get it properly installed. Had to take to a repair center for completion.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerLinda from Greenfield IN

Broken cog on gear

Researched the internet for a diagram of the mixer and used that to take it apart, clean everything, then install the new gear and new grease. Works great so far.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customerconradt from el paso TX

Last repairperson broke the top cover of the gearcase ; still need this part .

Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJamie from Jamestown ND

Gear teeth worn off worm gear

replace worm gear

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

Customerkarl from Eureka MT

Gears were stripped from overload of bread dough

At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Worm Gear

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRonald from Anna OH

Teeth missing on worm gear

removed cover annd snap ring removed gear and replaced with new,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 21