756514-1-S-GE-WH11X10033        -Knob Dial
756514-1-S-GE-WH11X10033        -Knob Dial 756514-2-S-GE-WH11X10033        -Knob Dial

Knob Dial

PartSelect Number PS756514

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not start.
  • Compare At

    $20.75
  • You Save

    $3.46
  • Your Price

    $17.29
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Knob and Clip

Part Number 268451

$6.62
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 4 reviews What's this?
1-4 of 4
 

29 of 31 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerScott from Denver CO

Dial broke off knob. Knob stripped.

Too easy! Push on dial, push on knob, insert clip. Done. Back in the day a repairman would have probably sold me a new timer with that knob and dial!

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerKelly from Lewiston ID

The edge of the knob wore out

I pulled the old knob off and put the new one on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDavid from Glenside PA

Washer stopping during cycles

First, I removed the control knob by pulling it out and then used needle nosed pliers to pull the plastic retainer clip from the back side of the knob and then slid it off. I then removed the large dial knob by simply pulling it off. Next, I removed the 4 torx head screws holding on the front control panel and the whole panel came off (the 4 screws are on the top side of the panel towards the rear). I then removed the connector block from the timer mechanism and then removed the single hex nut screw which holds the timer in place. There are two plastic tabs on the bottom of the timer which fit into slots on the panel. You can simply lift the old timer mechanism out by pulling it up and out. The new timer is installed by doing this in reverse. You then tighten the hex screw and then put the connector back on the new timer. You can then put the panel back in place and put back the 4 screws taken out earlier. Next, you push the indicator dial onto the timer shaft (lining up the notch in the dial with the tab on the timer shaft). Finally, you pull the retainer clip on the control knob partially out, push the knob on the timer shaft and then using a screwdriver, push the retainer clip into place and then push the control knob all the way onto the timer shaft.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerJames from Ephrata PA

Teeth were stripped on dial

Just followed your instructions,which were very good and simple.Took old one off then put the Knob Dial on and it clicked right on..Very,Very easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4