Quick Question!

Have you ever purchased from PartSelect.com before?

755842-1-S-GE-WE1M504           -Drum Bearing Slide - White
755842-1-S-GE-WE1M504           -Drum Bearing Slide - White 755842-2-S-GE-WE1M504           -Drum Bearing Slide - White http://www.partselect.com/Schematics/GE/00002276i02.gif

Drum Bearing Slide - White

PartSelect Number PS755842

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This is a white plastic part that is sourced directly from the manufacturer. Although the part is sold individually, it is recommended to check the other slide because they often wear at the same rate, and should be replaced at the same time. The drum bearing slide may need to be replaced if the dryer is not tumbling, takes longer than usual to dry clothes, or is noisy.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will Not Start.

Compare At

$8.22

You Save

$1.37

Your Price

$6.85
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Drum Bearing

Part Number 960316

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. This is an OEM part and is sold individually. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing.

$44.72
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 163 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Barbara from SICKLERVILLE, NJ

There was screeching noise during the drying cycle. Clothes being dried were getting stuck in the upper bearing.

I followed the instructions given in the video I watched when ordering the parts. Very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Phillip from Kissimmee, FL

Loud noise

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Ken from Westminster, MD

Clothes being eaten first then the loud noise

I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kerry from New Martinsville, WV

Noisy like a chain rattling inside

Disconnect Power from the Dryer
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unsnap bearing from front panel. Snap new bearing in place
and reassemble. Turn power back on.

When ordering drum bearing also order 1 set of Front Dryer
Drum Slides and 1 set of Drum Slides. You need both. Also
you should probably check the rear bearing. This would save
you time and shipping. I didn't and it cost me another
shipping charge as well as a couple of extra days downtime.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drum Bearing Slide - White
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Al from Elmhurst, IL

The front drum glides wore out

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Patrick from Madisonville, LA

Front dryer drum bearing wore out

Our gas GE "Eterna" King Sized capacity dryer started squeaking one day. I was suprised since the dryer was only a few years old, but assumed some grit had invaded and worn a bearing in the belt tensioner. My wife and I have three kids, so we use the dryer daily. The sound got louder quickly and finally it was so loud I had do something. After unplugging the appliance I took the top off the dryer (two screws in the top of the door jam) and the front off (two screws at the top of each corner) and in doing so saw that the drum bearing, which is just a round plastic
"shelf" on which the tumbler drum rides, suspended over the door, was worn through. There were four little "slides" on the bearing surface, and all but one was worn down to dust. I ordered the replacement bearing and slides (two white, I didn't know I also needed two green and have since bought them too) from Part Select and they arrived in about three days. In the meantime I re-assembled the dryer easily and we did use it once or twice, shrieking. When the parts came in I installed them in about 20 minutes, screwing the new bearing onto the rear surface of the front panel, right over the opening for the dryer door. The dryer has worked perfectly since. I used one Phillips head screwdriver for the whole job and paid about $50.00 for the parts. I work in an office and I travel, and when I was a kid I fixed my own cars and stuff, but I'm no appliance repairma! Nevertheless, this was easy! I assume I saved at least $100. The dryer works perfectly and more importantly, it's quiet again!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: robert from woodstock, GA

Squeaking noise

Dryer was making a horrible noise. When I took it apart I noticed that the from side dryer bearing was ruined. Ordered the part with the slide bars and replaced...Works great...

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drum Bearing Slide - White
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: philip from pickens, SC

Replaced drum bearing front and rear

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Glenn from Crown Point, IN

Dryer making high pitch squeal

Remove top (2 screws) and front (2 screws), snap out old drum bearing, put new slides in new drum bearing and install in dryer. Reinstall front and top of dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Maumee, OH

Worn drum slides and drum bearing

Removed two screws to remove top to access drum. Removed two screws to remove front panel. Easily removed drum bearing and snapped in new bearing. 4 Glides were slid into slots. Only one problem. My service parts list called for drum bearing #WE3X37. I was sent #WE3M26. I was assured this was the right part for my dryer. Although the part did fit, I was unable to use the existing light because the the hole on new bearing was too small to accommodate it. Replacement of drum bearing would not be necessary if GE would put visible labels on dryer warning consumers of preventive maintenance of glides that wear.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: JAMES from AKRON, OH

Dryer making load noises and not drying enough

I replaced drum bearing,dryer drum slide and lower front felt drum seal and everything works like brand new and did not take very long to replace all of this parts very easy job too do your self

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Jack from Avon, OH

Loud noise while running.

This took less than 10 minutes to complete. 1) pull off the top of the dryer and remove the two screws that attach the front panel to the side panels. Once you pull the front panel towards you, away from the side panels, you can remove the front bearing. Be sure to be careful not to pull apart the wiring on the left side of the front panel. If you do, it is easy re-attached by hand. The front roller bearing of he drum can be removed by hand. Simply pull upward, with a steady pressure, on the bearing. It will snap out with this gradual pressure. The slide can be inserted by hand, with the two gray slide at 11 and 1 o'clock and the wite slide at 10 and 2 o'clock. The new bearing will snap into place by hand. Carefully insert the light bulb into the hole in the top of the new bearing whle snapping into place. The web site provides a good diagram that illustrates the various pieces and assembly. Once the bearing is in place, lift the dryer drum and set on top of the bearing as you re-attach the front panel to the side panels with the screws removed earlier. Replace the top by snapping back into place. Less than 10 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Vener from Lemoore, CA

Loud noise and vibration

It's so easy, a caveman can do it! Watch the video on how to take it apart and while you have it open, grab a shop vac and clean around the area where you don't normally see. I replaced the top bearing since it was worn out pretty bad. The drum slides ( white and green ) which comes in pairs, were already gone. Put everything back together and works like new. No more squelling and vibration that sounds like my dryer was ready to come apart. Very fast on shipment. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Chris from Franklin, NH

Very noisy squeaky dryer

The dryer was very noisy when it would start. The drum had warn the pads out and the drum was riding on the drum bearing. It really isn't a bearing more of a big piece of plastic. On the bearing are 4 slides (2 white and 2 green). These are easy to replace if the bearing is good. I let mine go too long and wore part of the bearing off. To fix: UNPLUG! Open the door and find 2 screws facing upward screwed into the top. Remove these 2 screws and remove the top. Take notice of how it comes out of the dash. On each side of the front panel (from inside) there is a smaller screw with a bigger head, remove both of these. You can now lift the front panel away from the drum and pull the front panel right out. It would be a good time to take a shop vac and clean all the lint out of this. Mine was almost full. If you are changing the bearing it is held in place with clips built on the bearing. Remove and replace. Put on the new slides as well. There is a little tab on the bearing and a hole in the slide. put the hole over the tab. The green ones I put on the top and the whites on the outter sides. Put the bottom of the panel in first and line up the drum on the new bearing, replace the 2 big headed screws, line up the top in the dash and lower into position, replace the 2 screws up inside the door and you are done. I have no dryer experience and would rate this job on a scale of 1-10 to about a 3 or a 4. There were no real suprizes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Larry from PHOENIX, AZ

Dryer screeched when running

Dryer started making screeching noises while running, got progressively worse. Without taking it apart first, I ordered a front drum bearing and slides because this site said it fixed the problem the majority of the time. The site said replace the slides in pairs, but there are actually four. I picked up 2 more at a local appliance store, at roughly twice the price. Turned out I didn't need th replace the plastic piece called drum bearing, just the 4 slides that clip onto it. It is really easy to get the top and front off with just a phillips screwdriver. I did not check the rear center main bearing, as it requred removing the drum. The squealing lessended but it still was bad. Took it back apart and pulled the drum, and fount the rear main bearing bad. I found one at the same local store for only 2 bucks more than on this site. This was a bit more of a hassle, you really need two people to get it mounted to the drum. Tip-pre thread the holes with the self tapping screws, it makes it easier to get it together. There was a bit of lint build up under the drum heating element cover, so it was good to clean that out. Also blew all the dirt out of the motor with compressed air and shop vac. There was a access panel on back to get to the motor and belt tensioner. Got the dryer all buttoned up and now it runs nice and quiet.

Help other customers find the most helpful instructions.

Were these instructions helpful?