755842-1-S-GE-WE1M504           -Drum Bearing Slide - White
755842-1-S-GE-WE1M504           -Drum Bearing Slide - White 755842-2-S-GE-WE1M504           -Drum Bearing Slide - White

Drum Bearing Slide - White

PartSelect Number PS755842

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Compare At

    $7.26
  • You Save

    $1.21
  • Your Price

    $6.05
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Drum Bearing

Part Number 960316

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

$24.57
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 153 reviews What's this?
76-90 of 153
 

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from Schoharie NY

Loud screaching sound

First replaced the four drum slides,the lower front felt drum seal and the Drum bearing... Dryer still made LOUD screaching sound.. so I ordered and replaced the Rear drum bearing.And put a new drive belt on it being I had it all apart...Dryer now runs like its brand new.. My Dryer is over 10 years old. Cheaper to fix than replace... As far as Installation goes Was easy...Just watch the repair video or read the other post.. very helpfull...

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerJAMES from LEBANON KY

Dryer made a bad grinding sound sometimes

TOOK OFF CONTROL PANEL,TOP,LEFTSIDE FACING DOOR,AND,DOOR PANEL.REPLACE THE 2 GREEN AND 2 WHITE SLIDES, THE FRONT DRUM BEARING, THE REAR BEARING AND GROUNDIND STRAP BEHIND THE HEATING ELEMENT,AND NEW BELT.PUT BACK TOGETHER,RUN'S AND SOUNDS LIKE NEW. THE HARDEST PART WAS PUTTING DRUM BEARING IN INSIDE AND BACKSIDE OF DRUM BY YOURSELF.REPLACE BELT WITH LEFT SIDE PANEL OFF. EASY TO GET ON THAT WAY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

Customermatthew from newport news VA

A noise coming from the dryer

I first unplugged the dryer and moved to an open area to work on it. I then removed the three screws that held the access plate to disconnect the drive belt from the motor. Second I removed the two screws that held the top cover on then I removed it and set it aside. Third I removed the control station the thing with all the knobs on it that was about 11 screws (there were a mix of different types of screws some were Hex, Torx and Square tip). Fourth I removed the two screws that held the front door assembly on. I did not need to disconnect any wires to the front door.Fith I removed the Drum assembly by lifting and pressing outward on the outside walls of the frame I then carried the drum and set it on secure surface and then removed the three screws that held the bearing in from the inside. After cleaning the dryer after all components were removed I then removed the heating element that holds the bearing sleeve. I then started putting things back together in reverse order until it came time for the front door upper slide assembly that came off pretty easily it just clipped on I put the white and red sliders on first then I put the whole thing on it just clipped on then I put the front door on and screwed it on and finished putting things back on in reveres order. Then plugged it up and gave it test run and no noise and it runs great I hope for another ten years.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerdouglas from mooers forks NY

Front bearing and slides worn

First looked up on Google how to correct the squeak. Almost got into an internet trap by a you tube video looking to seel the slides for $20.00 (white) & $24.00 (green) each but luckily found your website. I originally ordered just the slides (first order) then aferwards ordered everything. Replacement parts fit right in without any struggle.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMichael from New Castle IN

Loud squeaking noise

Order and repair went fine. Just followed installation instructions already posted. However, after the repair it would overheat and shut off. Tested thermostats and they were good. Forums repeatedly talked about air flow problems but I knew it was clean. Ended up putting foam weather stripping on inside of front panel where it meets duct of squirrel fan and that fixed it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerEdgar from Edmunds WA

Dryer drum was squeaking.

Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 16 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

Customerbilly from kissimmee FL

Noise in drum

i took the front load dryer apart found the parts that were bad ordered the parts which were a snap at partsselect at first i thought it would be tuff to put back together but the site has good pictures i put the dryer back together but had a tuff time with the belt after i watched a video it went right together i found that taking pictures with my cell phone while taking things apart helped a lot when putting it back together all in all im proud of myself i didnt think i could do it but i did and the dryer works great i will be using the site again i used it a few months ago for my washer it it worked great too!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drum Bearing Slide - White

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRichard from Williston VT

Dryer squeaks and squeals while running

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerSteven from Lexington SC

Dryer squeaking, vibrating.

UNPLUG DRYER FIRST.Open dryer door find 2 screws at top of dryer door opening ( pointing upward). Remove screws and pop top panel of dryer up and remove it. Remove 2 screws near top of front panel (on the inside facing toward you). Careful not to drop them down into dryer interior. Pop front panel with door attached forward by tilting toward you. then lift off bottom tabs and turn panel / door assembly to the side. Careful not to pull wires at bottom loose. Carefully pop "Drum Bearing" off. This is the half moon shaped part that the "Drum Slides" (2) clear and(2) "green" pop on to. Replace drum bearing. Put new slides (4) on drum bearing. Replace felt seal. Place front panel back on dryer by carefully lifing dryer drum up while pushing front panel onto dryer. This allows the drum to "sit" on the felt seal. Put screws back onto top of front panel. Replace top panel , which can be tricky, by aligning tabs near contol panel with slots on top panel then lowering front of top panel into place. Then put screws back near top of door opening to secure top panel. Test dryer by turning off the heat on the heat setting knob and allow dryer to run for a time. Then try it with some clothes and heat. If it is still making noise then check rear bearing/bushing. Mine was fine and this repair fixed the issue. By the way, all but one of my 4 slides were worn to nothing and the drum had been "eating" into the "drum bearing making it paper thin in several areas. The felt was worn out also. This allowed the drum to settle down and gap at top which allowed clothes and dryer sheets to get caught between drum and dryer cabinet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerClifton from Donaldsonville LA

Loud squeaking

FOLLOWED THE INSTRUCTION VIDEO AND FOUND IT PRETTY EASY. IT TOOK A LITTLE LONGER DUE TO CLEANING ALL THE OLD LINT OUT OF THE UNIT. ITEMS CHANGED FIXED THE PROBLEM AND WORKING LIKE NEW.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPamela from Mouth Of Wilson VA

The drum bearing and slides worn out

The dryer literally ate my clothes!! We took the front cover off the dryer, removed the old parts and snapped in the bearing, felt seal and slides and now it just dries....it doesn't eat anything.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJeanne from Owensboro KY

Screaching

I have always been mechanically inclined so when my dryer started making noise I turned it into a family project. I found your website and studied what could be the problem. My 13 year old son and I took the dryer apart and found that it was the front drum bearing. i ordered the parts and my son did most of the work. Only had to take out two screws holding the top on and two holding the front. Vacumed out lint and followed directions on your site to replace parts. up and running in about 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerLaurie from Lawrenceville GA

Very loud noise.

Took the front & top off the dryer. Saw that the slides were missing or broken. Got the parts and put it back together. Works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drum Bearing Slide - White

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSteve from Sacramento CA

Dryer drum squealling

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drum Bearing Slide - White

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerGUY from BEDFORD HILLS NY

Drum slide wore - damaged drum bearing

r/r parts unit runs great

Help other customers find the most helpful instructions.

Were these instructions helpful?

76-90 of 153