Quick Question!

Have you ever purchased from PartSelect.com before?

755842-1-S-GE-WE1M504           -Drum Bearing Slide - White
755842-1-S-GE-WE1M504           -Drum Bearing Slide - White 755842-2-S-GE-WE1M504           -Drum Bearing Slide - White http://www.partselect.com/Schematics/GE/00002276i02.gif

Drum Bearing Slide - White

PartSelect Number PS755842

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will Not Start.

Compare At

$10.76

You Save

$1.79

Your Price

$8.97
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Drum Bearing

Part Number 960316

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

$44.28
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 157 reviews What's this?
151-157 of 157
 

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Dave from Ottawa, IL

Dry drum was squeeking

Replased drum slide, and wear bearings.
Very easy repair, and the squeeking is gone!!

Thanks for the easy ordering and fast delivery!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: David from Lawrenceville, GA

Squeaking and black marks on clothes.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Todd E from Eaton, OH

Makeing a squeaking noise

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Stephen from CORNWALL, NY

The dryer was squeaking like a recently castrated banshee

I first removed four screws above the door opening to lift off the top, then removed two screws, near the top, inside the front, to remove the front. There I found that 2 grey plastic and one white plastic anti-friction strips were worn to nothing (even the large plastic bezel that incorporates the light was starting to wear away, from just a few days!).

When I went to put the front back on, i couldn't get the lip of the drum to ride properly on the felt. In fiddling with it, the drum fell off the rear bearing, too, so I put it back on.

So I ordered new felt, two white and two grey strips (I didn't know if 1 or 2 were in each $8 "kit"--only one per kit), a spare belt--just in case--and some bulbs.

Putting the strips on was easy--15 seconds each. Putting on the felt took all of 20 seconds. I spent more time scraping off the dust and vacuuming things out!

The drum fit over the felt quite easily now, and when I ran it, it was wonderfully quiet. For a minute! Then, it started making a new, grinding noise!

I had a Sears repairman friend come over, and he found that a small platic bushing had fallen off the rear bearing element. Once he put that in place, it all worked perfectly. Beautifully quiet!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: James from Beaufort, NC

While cleaning dryer for low exhaust discharge pressure, I observed one slide (green) 98% worn down, the other three 90 to 95% worn and felt drum seal broke in half.

Opening the dryer door and removed the two screws located at the top of the opening. Pop off top lid of dryer by lifting up on front, and slide forward. I needed to break it loose by prying it up with a screw driver (use light pressure, be careful not to bend/scrape top), as it was first time every being removed. Remove two screws at top of front panel, hold up drum, and pull front panel forward. Unplug electrical cable to door, and removed front panel. Removed and replaced all four slides (2 Green slides & 2 Clear slides). Removed felt drum seal and replaced by lightly pushing in slots (couple of very light pushes using a screw driver was also needed). Placed front panel back on slots at bottom of dryer (REMEBER TO PLUG IN DOOR SWITCH), lifting (lightly) up on drum, and push in place, replaced all parts in reverse order. Top was a little tricky getting back on, but with a little push it snapped in place. Plugged in dryer performed test run everything worked perfect. Thanks to PartsSelect for their quick response to my order, you are definitely on my favorites listing for any future repairs and/or help.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Steven from Lexington, SC

Dryer squeaking, vibrating.

UNPLUG DRYER FIRST.Open dryer door find 2 screws at top of dryer door opening ( pointing upward). Remove screws and pop top panel of dryer up and remove it. Remove 2 screws near top of front panel (on the inside facing toward you). Careful not to drop them down into dryer interior. Pop front panel with door attached forward by tilting toward you. then lift off bottom tabs and turn panel / door assembly to the side. Careful not to pull wires at bottom loose. Carefully pop "Drum Bearing" off. This is the half moon shaped part that the "Drum Slides" (2) clear and(2) "green" pop on to. Replace drum bearing. Put new slides (4) on drum bearing. Replace felt seal. Place front panel back on dryer by carefully lifing dryer drum up while pushing front panel onto dryer. This allows the drum to "sit" on the felt seal. Put screws back onto top of front panel. Replace top panel , which can be tricky, by aligning tabs near contol panel with slots on top panel then lowering front of top panel into place. Then put screws back near top of door opening to secure top panel. Test dryer by turning off the heat on the heat setting knob and allow dryer to run for a time. Then try it with some clothes and heat. If it is still making noise then check rear bearing/bushing. Mine was fine and this repair fixed the issue. By the way, all but one of my 4 slides were worn to nothing and the drum had been "eating" into the "drum bearing making it paper thin in several areas. The felt was worn out also. This allowed the drum to settle down and gap at top which allowed clothes and dryer sheets to get caught between drum and dryer cabinet.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Tod from Cherry Valley, CA

Loud squeaking

remove to screws in front to take of top. Then remove two screws holding the face on. change parts re assebmle. extra hands nice for holding drum while remounting face. Nice and quiet now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

151-157 of 157