755799-1-S-GE-WE01X10167        -Rotary Selector Knob
755799-1-S-GE-WE01X10167        -Rotary Selector Knob 755799-2-S-GE-WE01X10167        -Rotary Selector Knob 755799-3-S-GE-WE01X10167        -Rotary Selector Knob

Rotary Selector Knob

PartSelect Number PS755799

This knob accepts a D-shaped shaft.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $45.88
  • You Save

    $7.65
  • Your Price

    $38.23
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Rotary Knob

Part Number 755798

$41.06
In Stock

Timer Knob

Part Number 783664

This knob accepts a D-shaped shaft.

$43.79
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 3 reviews What's this?
1-3 of 3
 

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerJeffrey from Washington PA

Replace upper drum-glide & felt. Also replaced lower felt

Unplugged and raised the top of the dryer (This allows access to the screws that attach the front of the dryer to the body of the dryer). 2nd- removed the two screws inside the front and down approx 5 inches on each side of the front. Also remove the small plastic tie-wrap that holds the wiring to the top of the dryer. It will be on the right hand side if facing the front of the dryer. Unplug the two plastic wire plugs that attach the wiring to the controls. Use a flat screw driver to pry the front away from the body of the dryer (this will unattach clips that hold the front in place. Remove the felt guide. The factory glue will keep some of the felt attached to the housing. This is where I used the utility blade to remove the rest of the felt. Then I used the soft wire-wheel to remove the rest of the residue of the glue. Probably not necessary. I replaced the top felt first with the teflon guides on it. I used spring loaded clamps to hold it in place. The clamps were probably not necessary either because the glue holds very well. Next I replaced the lower felt. While the front of the dryer was removed this was a good time to use the nozzle on the sweeper to remove the lint that was built up inside of the dryer. Reverse your steps and put your dryer back in service. You may need to reach through the door to align the drum over the felt in order to re-attach the front of the dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerPete from Carlsbad CA

Broken start switch

Screwdriver on right and left of the top to pry it off the top panel spring clips.
rotated the switch assembly by hand from the back to remove it from the front panel.
removed the connectors and connected them to the new switch.
Put the new switch in and rotated it to mount it to the front panel.

Thank you for your help. I ordered a switch and a knob for a GE dryer.

A neighbor had this washer and a dryer sitting in their driveway—getting rid of them because of a broken switch and knobs.

A repair man told them it would be $250.

My neighbor gave the washer and dryer to me for free and I gave them to a single Mom who was in need.

The repair took me 10 min and cost me less than $75 thanks to your web site help.

Here’s a tip for owners of a GE Profile washer and dryer—The plastic knobs are weak and split where they connect with the switch. Pull them off and wrap (6-8 times) the outside diameter of the connection part of the knob with electrical tape.
Do-it-yourself with partselect.com!

Pete Haas
Carlsbad CA

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerAndre from Newport News VA

Plastic knobs broken at the base.

I pushed the new knob into place and voila!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3