755622-1-S-GE-WD28X10103        -Third Level Spray Arm
755622-1-S-GE-WD28X10103        -Third Level Spray Arm 755622-2-S-GE-WD28X10103        -Third Level Spray Arm 755622-3-S-GE-WD28X10103        -Third Level Spray Arm

Third Level Spray Arm

PartSelect Number PS755622

Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack. This spray arm does not come with the screws.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Not cleaning properly.
  • Leaking water.
  • Compare At

    $14.10
  • You Save

    $2.35
  • Your Price

    $11.75
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

SCREW

Part Number 261505

$2.14
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 7 reviews What's this?
1-7 of 7
 

28 of 40 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerAaron from Liberty Township OH

Washing poorly, leaving particles of food on top of the dishes, not draining completely, ceiling spray arm not spinning (bent up to the ceiling)

The lower spray arm unscrews. From inside the dishwahser, put a screwdriver through the tab slots and unscrew the tower from the floor. It's pretty tight for plastic.
The upper spray arm has screws on the top of the dishwasher. You must slide the dishwasher out from underneath the countertop to get to the screws. Normally that's just the two screws above the door that screw into the countertop. Pull the insulation back and unscrew the arm from the top of the dishwasher. Reverse to reinstall.
Piston and nut assembly for check valve: Inside the dishwasher at the back there are 2 screws that hold a screen down. Remove the screen. Take out the check valve and replace it. It was still functional in mine, it looked like food gunk had built up on it and impeded the check valve action.
The flapper chec is a rubber flap in the drain tube that connects to your sink drain. You have to pull the dishwasher out from under the sink to get to the end of the drain tube that connects to the dishwasher. Take the hose clamp loose and remove the drain tube from the dishwasher. Then unscrew the plastic fitting that you just took the drain tube off of. The flapper chec is there. It had turned brittle and didn't flap anymore. It is a similar setup to the rubber seal at the end of your garden hose.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Third Level Spray Arm

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Norman OK

Replace top spray arm

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Third Level Spray Arm

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerCarl from Corpus Christi TX

Dishes not clean after wash,white film all over.

Pulled unit out of cabinet took two top screws out of spinner spray arm and put back together.Old sprayer was plugged up not letting wash go through.Thanks for helping me fix and not replace unit.Saved at least 400.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Third Level Spray Arm

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJAMES from AUBURN WA

Spray arm falls off

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Third Level Spray Arm

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerDebra from Hooks Town PA

Upper spray would fall off

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerKurtis from Morristown MN

Leaked from the top of dishwasher

Used a nutdriver to remove the two screws attaching the third level spray arm and a pliers to release the clamp holding the power shower hose. Reversed the process on the new hose and spray arm. Dishwasher works great now!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerSteven from Oakdale NY

Leaking from the hose that connects to the upper spray arm

replaced hose and upper sparay arm

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7