Quick Question!

Have you ever purchased from PartSelect.com before?

754418-1-S-GE-WB44T10043        -Broil Element
754418-1-S-GE-WB44T10043        -Broil Element 754418-2-S-GE-WB44T10043        -Broil Element http://www.partselect.com/Schematics/GE/00121753i03.gif

Broil Element

PartSelect Number PS754418

This broil element is found on the roof of the oven.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little to no heat when broiling.
  • Element will not heat.

Compare At

$74.24

You Save

$12.37

Your Price

$61.87
Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 4 reviews What's this?
1-4 of 4
 

17 of 18 people found this instruction helpful

Parts Used:
  • Broil Element
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: robert from pine valley, CA

Broil (top) element replacement for oven

After turning the breaker off, using a 1/4 inch nut driver I removed all the clamp screws (5) holding the heating element in place. I then unplugged the element wire spades from the rear of oven and removed the old element. Installing the new one was simply going in reverse order. After plugging the new one in, I did however, use plyers to squeeze the connectors and make the connections tighter. It took a little more back work than I thought because I was leaning over most the time. All in all, I saved a hundred dollar bill in doing this 30 min job myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Broil Element
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Joseph from Beaumont, CA

Broken bake element

I unfastened the three 1/4" rear screws, then the two support screws on top. I pulled the old element out,( plenty of slack wire luckily). disconnected it from the bayonet-type connections, then attached the new element. I secured the new element using the 1/4" screws. Bingo!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
  • Broil Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers, Socket set
Customer: ROBERT P. from Santa Fe,, NM

Burnt broiler element

Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
  • Broil Element
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Ron from Irvine, CA

Broiler element failed

Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mounting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4