This broil element is found on the roof of the oven.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Little to no heat when broiling | Element will not heat
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo.
This part works with the following products:
General Electric, Kenmore.
Part# WB44T10043 replaces these:
AP3190731, 963475, WB44K10007
Customer Reviews
Average Rating:
★★★★★
★★★★★
5 Reviews
4.2
Filter By Rating:
5 Stars
4
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
1
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Steve E - May 23, 2023
Verified Purchase
Broil Element
I installed it and it works.
★★★★★
★★★★★
Hub City Thrift J - December 26, 2020
Verified Purchase
Just what the doctor ordered
Fits great
Works great
Do it
★★★★★
★★★★★
Caroline M - April 27, 2019
Verified Purchase
Easy to replace
Exactly what we ordered and needed to repair my GE oven. Came super quick and I was back to cooking once more!!!!
★★★★★
★★★★★
JOSEPH G - September 19, 2018
Verified Purchase
Replacement Part
The part was received in a damaged box that had no internal padding. The broiler element was bent in at least 3 different areas. I don’t know yet if will work! I tried to bend back areas and installed, but have not checked to see if it is functional due to being hit hard with Hurricane Florence in NC and did not want to test until after the storm passed.
★★★★★
★★★★★
Curt K - July 20, 2018
Verified Purchase
Perfect match, simple swap
Identical to the existing part, replaced in less than 10 minutes.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 6 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Lower Oven Broiler Stopped Working
Turned power off to oven Unscrewed broiler nuts (total of 4) Pulled Broiler out from back of stove Disconnected wires Reconnected wire Remounted broiler and replaced bolts Turned power back on
Frank from PARKER, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Remove and replace Broil (upper) heating element.
Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch). Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper). Remove the racks (wire shelves). Remove the two 1/4" mount
... Read moreing screws that secure the heating element to the back and the two screws that secure the element to the top of the oven.. Gently pull the wires out and disconnect them from the heating element. Now reverse the process. Connect the wires to the new heating element in the same fashion as they came off. Push the wires and heating element back in place and secure with the four screws. Replace the wire racks (shelves). Replace the door (again, this is best accomplished with a helper). Turn the power back on. Run a test of the broiler to make sure the repair was completed properly. voila!
Read less
Russell from ARROYO GRANDE, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt Broiler Element
Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy
... Read more to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!
Read less
ROBERT P. from Santa Fe,, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler Element Failed
Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mo
... Read moreunting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.
Read less
Ron from Irvine, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Bake Element
I unfastened the three 1/4" rear screws, then the two support screws on top. I pulled the old element out,( plenty of slack wire luckily). disconnected it from the bayonet-type connections, then attached the new element. I secured the new element using the 1/4" screws. Bingo!
Joseph from Beaumont, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broil (top) element replacement for oven
After turning the breaker off, using a 1/4 inch nut driver I removed all the clamp screws (5) holding the heating element in place. I then unplugged the element wire spades from the rear of oven and removed the old element. Installing the new one was simply going in reverse order. After plugging the new one in, I did however, use plyers t
... Read moreo squeeze the connectors and make the connections tighter. It took a little more back work than I thought because I was leaning over most the time. All in all, I saved a hundred dollar bill in doing this 30 min job myself.
Read less
robert from pine valley, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
19 of 22 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Debbie
September 26, 2019
The broiler unit broke creating non-continuity in the actual element. Is the replacement part still available? I've found part number ap3190731, but am not sure this part will work with my particular model.I've only found parts for model jt965sk4ss. is this the same or similar product? would appreciate any help you can provide.
thank you.
For model number JT965SK4SS
Good Day Debbie. Thank you for your question in regards to your unit (Model Number JT965SK4SS) Based on our research the broil element that is compatible with your model is PartSelect Number PS754418. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
Was this helpful?
Thank you for voting!
Robert
November 22, 2019
You recommend using model # jsp47bf1bbb parts. The diagram shows this with two spreaders(?) but the blow up of the part only shows the rear one. Does this mean you should reuse the front spreader on the new part. The one i wish to replace has two spreaders with the front spreader used to fix the unit to the top of the oven.
For model number JSP47BOF1BB
Good Day Robert. Thank you for your question in regards to part number WB44T10043. Based on our research the part has been redesigned by the manufacturer with only one spreader bar. Hope this helps. Best Regards.
Was this helpful?
Thank you for voting!
Mel
January 26, 2020
I need to know the part number replacement for the broiler element on the above model. Thank you!
For model number JT915SK4SS
Hi Mel, thank you for your question. Here is that part for you: PS754418. Good luck with your repair.
Was this helpful?
Thank you for voting!
Chris
July 28, 2021
Hello. Our oven model is jt952s0k3ss. Can you let us know the part number of the replacement broil element? Thank you.
For model number JT952S0K3SS
Hello Chris, Thank you for contacting us. The broil element at the top of the oven is part# PS754418. Hope this helps.
Was this helpful?
Thank you for voting!
Thomas
November 2, 2021
The Broiler element works, but the bracket holding it in place has broken on one side, causing the element to sag on one side. Is there a replacement bracket available?
For model number 91147713200
Hello Thomas, Thank you for the question. The Brackets are only sold as part of the Broil Element, PartSelect Number PS754418. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Lori
March 26, 2023
What part will replace the broiling element in top oven?
For model number JT952S0K4SS
Hello Lori, thank you for reaching out. The broil element, part number PS754418, is compatible with your model. We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
