734247-1-S-Whirlpool-240775-1          -End Seal
734247-1-S-Whirlpool-240775-1          -End Seal 734247-2-S-Whirlpool-240775-1          -End Seal

End Seal

PartSelect Number PS734247

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $4.79
  • You Save

    $.80
  • Your Price

    $3.99
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.3 / 5.0, 4 reviews What's this?
1-4 of 4
 

20 of 22 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerAlice from Fort Myers FL

Leaking oil

This was my husband's first time to taking apart any mixer - much less a heavy duty KitchenAid. Since we could not find a local repairman, the only thing to do was try to repair it himself. Using your exploded view of the machine he found on the internet, he ordered a gasket which he felt would be needed to repair the mixer. When he tore the machine down, the problem was what he had suspected - original grease had liquified and the rest had turned black in color. He went to a local auto parts store and bought a can of wheel bearing grease. He cleaned out the old oil and repacked with about a half pound of the new grease. The most difficult part of the repair was inserting the roll pin to attach the ring gear housing to the output shaft. It was impossible for him to reinsert the original pin, so he bought a new tension pin with which he was able to work. The only part he has been unable to align is the lever to lock/unlock the machine. He managed to set it enough that it locks when the lever is pushed halfway. The machine works great but I would not advise a person without any mechanical ability to try to repair these mixers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert E. from Loveland CO

The worm gear (plastic-made to be the weakest spot), three teeth were worn,

I removed the lower unit along with the top unit, removed the gear, replaced the gear, then put back together. I removed the grease, saved most of it, then discarded what looked like the dirty grease. I cleaned inside thoroughly in case broken parts were inside. The three schematics were very helpful in re-installed. Mixer was 40 years old but works like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBruce from Petersburg MI

End seal broken and cover tabs broken.

Unplugged mixer. Removed screw holding cover on. Removed end seal. Inspected repair area for furhter damage. Installed new end seal and cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • End Seal

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerJames from Glendale CA

Worn worm-gear replacement

Repairing/replacing worm-gear (FSP part# W10112253) for a KitchenAid Stand Mixer model number K5SS. First: I am writing this story because all the videos or repair articles I’ve viewed are either misleading or incorrect in that they do not include older K5SS models. 1. These older models from the mid 1960’s or even earlier have four very large #4 chrome plated Phillips Head Screws holding the mixer base to the motor assembly and NOT four small machine screws (one with a lock-washer) as seen on other repair videos. In addition, the stand is composed of two separate pieces with the bottom half being held together with another four identical #4 chrome plated Phillips Head Screws. The upper four holding the stand to the motor housing (I used a manual impact driver to loosen the very stubborn, #4 Phillips screws) must be removed so as to access the four smaller Phillips machine screws (no lock-washers found here, best buy at least four #10, split, before reassembly) 2. Lastly, you will need two pin punches however the recommended smaller 3/32 inch is still too large to remove the pin in the tower assembly. You will need one size smaller or a #4 pin punch instead. These older Kitchen Aid mixers were built with very tight tolerances. Please be patient and take your time removing the pins. Good Luck……. Jim

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4