734018-1-S-Whirlpool-8539324           -Upper Spray Arm Mount
734018-1-S-Whirlpool-8539324           -Upper Spray Arm Mount 734018-2-S-Whirlpool-8539324           -Upper Spray Arm Mount 734018-3-S-Whirlpool-8539324           -Upper Spray Arm Mount http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/I3UBBVVU.gif

Upper Spray Arm Mount

PartSelect Number PS734018

**Please note: This is a redesigned part. The top mounting clip and screw are no longer needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Leaking.
  • Noisy.
  • Will not fill with water.
  • Door won’t close.
  • Compare At

    $7.27
  • You Save

    $1.21
  • Your Price

    $6.06
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 89 reviews What's this?
 

3 of 3 people found this instruction helpful

Parts Used

  • Upper Spray Arm Mount

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerLinda from Warrenton, VA

Plastic mount was broken for upper level.

We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerGeorge from Wayside, NJ

The upper rotor mount broke off.

I screwed the rack mount to the spindle using
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.

I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCharles from Hopkins, MN

Broken mount caused dishwasher to shoot water against door, caused leaking

Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerRodney from Pleasanton, CA

Upper spray broke off

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Spray Arm Mount

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerGeorge from Richmond, ME

The original washer arm shaft failed

The original washer arm mount was held with a clip and stainless screw. The replacement was a simpler snap clip, but the shaft was "heavier" plastic. I was doubtful with the snap clip, but I have had no issues in the past two weeks.
Remove the old orignial clip with screw. Remove and SAVE the washer arm retining screw. Look at the orientation of the new clip and shaft. The shaft should be canted to your LEFT so that the washer arm clears the bottom of the rack. Simple snap in install. If you guess wrong at first, simply unclip and reverse. Screw in the washer arm retaining screw. Viola!

Help other customers find the most helpful instructions.

Were these instructions helpful?