| |
3 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTom from Plano TX
Spray arm was broken
Went to parts select online, put in my washer info, the parts pulled right up complete with illustrated parts and it was very easy to order. The parts were actually at my door the next day, that was amazing. I think this is a very good source to get appliance parts.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRobert from Summit NJ
Spray arm broke off the mount
Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerAlan from Chicago IL
Mount for top rack spinner broke
Install too less that a minute. Fit perfectly.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCharlie from Springville AL
Mounting hardware was broken
Removed the screw that held the mount in place. Snapped the new mount place (no screws required).
Fast & easy.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerLinda from Warrenton VA
Plastic mount was broken for upper level.
We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGeorge from Richmond ME
The original washer arm shaft failed
The original washer arm mount was held with a clip and stainless screw. The replacement was a simpler snap clip, but the shaft was "heavier" plastic. I was doubtful with the snap clip, but I have had no issues in the past two weeks.
Remove the old orignial clip with screw. Remove and SAVE the washer arm retining screw. Look at the orientation of the new clip and shaft. The shaft should be canted to your LEFT so that the washer arm clears the bottom of the rack. Simple snap in install. If you guess wrong at first, simply unclip and reverse. Screw in the washer arm retaining screw. Viola!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJim from Modesto CA
Top spray washer axle assembly broke
I took out the screw holding the broken part, then I screwed in the new pivot/axle assemble and snapped it into the top rack. Super Easy!!! The items in the top rack get real clean now!
Thanks!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerMartin from Manalapan NJ
Cracked h2o mount, upr spray
Took about 10 mins. Only problem was that is was an updated part. Different color (no big deal), but mounting was different. The old mount had a stainless steel screw holding, and this one was just a "snap in". No bidg deal, working good...
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerilham from north haledon NJ
The upperspray arm mounting bracket broke
all i did is to remove the screws out take out the damaged ones and replace them the new ones put the screws back, it was very easy, it save me time and money. Thank-you part select.com
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRandall from Santa Rosa Beach FL
Top spray unit broke off
Received unit in two or three days even during Christmas rush.
Replaced sprayer with just a screwdriver in no time and dishwasher is working perfectly.
PartSelect is the only way to go. I have used them for other parts and they are always prompt and easy to identify parts on their website.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerPia from Pleasanton CA
Upper water spray arm broke off
My husband put too many things in the dishwasher and it interfered with the upper spray arm. The piece that fastens the upper arm to the top basket broke. Bummer....I run the darn thing at least once a day.
I ordered the part (super easy to do) and it was here the next day. (I only had to do one load by hand). I used a screwdriver to detach the arm, replaced the piece and screwed the new one in place. Five minutes-done.
My husband was impressed. Duh!
:-)
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customermark from Sumter SC
Part was broken
Extremely easy. Put part in the upper basket of the diswasher and hooked up the spay arm. If you know how it came off, you should know how it went back on, is the motto. The part fit perfectly and this website did a great job of pictures for comparison.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerWilliam from Indianapolis IN
Upper spray arm broken off
Removed one screw holding remainder of the upper spray arm bracket from the top basket. Removed one screw from the underneath side of the spray arm holding it to the Wash Arm Tube Holder. Attached the new Wash Arm Tube Holder to the spray arm, then the whole assembly to the top basket.
PartSelect was GREAT. The pictures on the web site made it easy to determine which part was needed. I ordered around 5pm and chose standard 3-day shipping, but to my surprise the parts showed up at 10:30 am the next day! I'll be back!!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerTodd from Dublin CA
Spray arm was loose and the mounting bracket was broken
Put the arm in place, secured with one nut, then underneath with a screw. I attached the little loop that holds the funnel part on and was done. The dishes in the upper rack have never been cleaner.
This web site is the easiest web site I've ever navigated.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBETTY from PETALUMA CA
The spray tube below the arm was all torn up
once I figured out the instructions it went really well.I was most amazed that I received part the next day! That was very fast. I will know where to go next time I need a part. I saved some money and your service is great. Also the vidio instructions are great.
|