Oven Door Trim Kit

PartSelect Number PS732532

This white oven door trim set contains three pieces: two for the sides of the door and one for the bottom. The screws are sold separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $40.42
  • You Save

    $6.74
  • Your Price

    $33.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Trim Kit - Black

Part Number 732886

This kit includes the 2 side pieces and 1 bottom piece. NOTE: This kit has been updated by the manufacturer. The lower screws are no longer needed for the side trim now locks in to the lower trim piece.

$36.38
In Stock

TRIM-DOOR - Bisque

Part Number 732887

Includes the 2 side trim and 1 bottom trim - Redesigned parts per Manufacturer.

$32.64
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 7 reviews What's this?
1-7 of 7
 

13 of 18 people found this instruction helpful

Parts Used

  • Oven Door Trim Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerDiann from Mesa AZ

Trim broke while cleaning door handle

well had I known that the trim did not go over the glass, the project would have been easy, but I thought the trim held the glass in, but that was not the case. After much juggling discovered that the trim went under the glass, and at that point the instilation was very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 18 people found this instruction helpful

Parts Used

  • Oven Door Trim Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerMatthew from Marlborough MA

Lower part of trim was badly rusted

Removed the trim by unscrewing 5 screws being careful not to drop glass panel. Had to scrape and paint over rust stains on the glass panel. After paint dried reinstalled with new trim (remodeled part only required 3 screws). Just a little tricky getting screws started while holding up the glass panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 15 people found this instruction helpful

Parts Used

  • Oven Door Trim Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerAnn from Whitewater WI

The side trim was broken when I cleaned the door.

The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 14 people found this instruction helpful

Parts Used

  • Oven Door Trim Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerCharles G from Apex NC

I broke one side of the oven door trim while cleaning

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 28 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJeanie from Anchorage AK

Replacement of oven glass door

Parts arrived extremely quickly. Easy assembly. Would highly recommend partselect.com. Thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerEarle from Taylorsville UT

Both hinges were bent, probably from dropping the door, or leaning on it when it was in the down position.

1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outside, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Oven Door Trim Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customermichael from Reynoldsburg OH

Broken trim

remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7