| |
7 of 9 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerFrank from Oswego IL
Original plastic fasteners on the rack adjusters wore out and broke
removed old rack adjusters by prying remaining fasteners with a screwdriver, then installed new ones with steel screws. Very simple, and adjusters are better than new now.
|
4 of 4 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerGordon from Lynchburg VA
Dishwasher upper rack fallen one side
POPPED THE OLD HOUSING APART WITH SCREW DRIVER, SAVING INTERNAL PART, INSTALLED PART INTO NEW HOUSING, PLACED IN POSISTION, INSTALLED TWO NEW SCREWS AND IT WORKED LIKE CHARMED. SO SIMPLE, I HAVE ORDERED 2ND PART TO REPLACE OPPOSITE SIDE WHICH IS NOT YET BROKEN. THANKS TO THE TERRIFIC PHONE ASSISTANT WHO CONVINCED ME IT WOULD WORK AND NOT HAVE TO REPLACE THE ENTIRE RACK WHICH WAS SUGGESTED BY A REPAIR MAN......MANY THANKS! ! ! !
|
2 of 2 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWalter from Issaquah WA
Plastic parts broke when applied pressure to top dish rack
Family member used rack as support when loading dishes in the rack. The plastic parts broke. Ordered the replacement parts and was easy fix, BUT you will need Torx 15 tool to get it done. So sad they used this screw to fix the dishwasher - would have been so much easier to use a normal Philips head screw. Add about $7.00 for the tool to complete the work, but very easy....
|
1 of 1 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerElizabeth from Naperville IL
Dishrack adjuster was broken
Ordered part to replace broken rack adjuster. Part came in a very timely fashion. Realized when I ordered the part that I was missing the "thumb tab" that allows you to do the adjusting. Sent in another order to this company and was confident it would be delivered promptly, which it was. I had a little trouble with the screws being a little tight for the holes they went in but other than that, very easy repair.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerkathy from holden MA
Original dishrack adjuster was broken on left side
Slight challenge removing old housing...once that was removed I was able to clean the area and slide the new pieces into place and secure with screws that were provided.
Parts arrived within 24 hours of ordering replacement! It was a terrific experience.!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJeff from West Jordan UT
Dishwasher adjust housing broken.
I'm not a very handy guy and normally don't do repairs. However I felt I could handle this one. I just removed the broken housing, looked the part up on partselect.com. Three days later I received the part and had the new one put on in about 20 min. The only disappointing thing was that the part required a star type end screw driver and lucky I had one or I would not have been happy.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJames from Grant Park IL
Original part cracked
The repair was very easy. Just removed the old part and put the new part in with two screws instead of the snap together plastic part. The two screws that came with the part had hex or star heads. I couldn't find my hex head set but a small phillips head did the job.
I would use this company again. Fair price. Fast shipping.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers, Wrench set
CustomerDaniel from River Falls WI
Primary problem door dropped open
I first replaced the door balance kit. I had to unhook the water supply to pull the unit out. I replaced the door balance kit first. The pieces were slightly different than my old parts, but fairly easy to figure out. Also, the spring was off on one side so had to confirm where to reconnect it. That took about 30 minutes. I then took out the racks and installed the chopper. The old one came out easily, but it took about 20 minutes to seat the new chopper properly and then reassemble the lower arm. This part of the repair was about another 30 minutes total. Lastly, I replaced the upper rack adjusters, which had broken a while ago and I had pulled together with nylon straps. The new adjusters have metal screws which should be more durable than the plastic clips used in the original equipment. This part of the job took about another 20 minutes, but was easy to complete. The dishwasher door works like new and the top rack is easier to load with the adjusters working properly again.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMark from Portland OR
Top dishrack adjuster pins broke that holds the two main pieces together
I first had to remove the existing adjuster from the rack that was still attached. Once removed it was just a matter of sliding on the new part. The second piece of the adjuster which holds the adjuster to the rack was then screwed on to the first piece with supplied screws. I didn't think that the supplied star shaped screws were necessary. Why not just a philips?? I did have a little trouble getting the rack extended out far enough to clear the dishwasher in order to screw in the back screw of the adjuster.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJon from San Rafael CA
Upper rack couldn't be raised - stuck in low position
Pry the inner and outer pieces of the old adjuster apart, setting the lever part aside and noting how it fits between the two pieces. Put the lever into the larger of the new adjuster pieces and hold the rack at the right height so the two new pieces can snap together tightly around the rack. Then simply drive the screws in with a screwdriver. It would be easier to have another person hold the pieces together while you drive in the screws.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerTheresa from Sheridan MT
|
0 of 2 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJolene from Constableville NY
Dishrack adjuster housing snapped & broke when I caught the rack on somthing when pulling open.
It's very easy to repair. You put the new parts back in the same way as you took the broken parts out. You receive 2 screws instead of the orginal push in clips that hold the parts together. The screws are very easy to put in but you will need a Torx head screw driver.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Dishrack Adjuster Housing
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerRobert from Monument CO
Borken upper dishrack height adjuster on one side.
Took off what was left of the old one and put the new one on using the old intact adjuster lever part (goes inside the adjuster). With this part the push fit snap pins are not required because there are screws provided with the part. The screws are star-drive. I have a driver kit that has star-drive bits, or I would have been mad. The drive type should be mentioned in the description for the part (unless I missed it), and also it should mention that the press-fit pins are not required.
|