Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS6447706
Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
This was very easy. The utility room is just off the kitchen. I had your repair video running on my laptop on the kitchen island and started at ~8am last Saturday. A very fun project, because all the guesswork has been eliminated by watching your repair video for a few moments, hitting pause, then doing exactly what was explained on the video. I took the time to vacuum out every piece of lint, then carefully reassembled the dryer. One bit of advice- - if you need to disconnect any wires, mark them with a Sharpie pen: one dot on both the wire and the spot you pulled it from, two dots for the second wire, etc. At reassembly time, it's a snap. Also, as you remove screws, keep a few sandwich bags handy so you can group screws together. Have fun!
Help other customers find the most helpful instructions.
Were these instructions helpful?
I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier
Followed the instruction video and found it pretty easy. It took a little longer due to cleaning all the old lint out of the unit. Items changed fixed the problem and working like new.
Disconnect power. Removed 2 screws from dryer door to dryer top cover. Removed dryer top cover. Remove two screws from dryer front panel to dryer side panels. Lift front /door panel up and swing to side. Remove old dryer drum bearing. Install new drum bearing and slides. Assemble dryer.
I have always been mechanically inclined so when my dryer started making noise I turned it into a family project. I found your website and studied what could be the problem. My 13 year old son and I took the dryer apart and found that it was the front drum bearing. i ordered the parts and my son did most of the work. Only had to take out two screws holding the top on and two holding the front. Vacumed out lint and followed directions on your site to replace parts. up and running in about 30 minutes.
Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!
Unplug the dryer from the wall. I took the door off by removing the 4 screws that held it on. Removed the 2 screws in the top of the door frame to allow the top to come off. The top lifted off and slid to the left about an inch to release it from the panel. There are 2 screws in the cabinet on the top left and right. Remove these and the front panel will pop off. You can disconnect the closed door switch if you want to but not needed to complete the job. The worn drum bearing pops out with a little force. Attatch the new glides to the new drum bearing. Your old bearing may have only had 2 glides, mine did. I installed 4 as there are slots for 4 glides. Remove the punch-out disk at the top of the bearing. Starting with the bottom, snap the new bearing into place. Remove the old felt. I started at the middle of the lower drum bearing using the middle of the felt and pushed it into the slot provided. Making sure the drum is positioned correctly in the bearing, close the front panel and reinstall the screws. Putting the top on requires a little finesse, just work with it and it'll work for you. Reinstall the screws in the top of the door frame to the top panel. Reinstall door. Plug in and test. It may make a rubbing noice but this should go away after use and the glides get worn in.
Unscrewed the screws that hold the front of the driver in place. Replaced the felt and drum slides. Reattached front of dryer. The dryer is as good as new....
I followed other peoples instructions and comments on how to remove front cover, Thank you to them. It made this job simple to do. Them I replaced all of my parts that i ordered. Dryer works and sound great Thanks Again.
replaced drum slides and bearing
First I took the dryer apart to see what the problem was and found that the felt dryer guide had come off it's mount and was broken. Next I saw that the dryer glides were worn away and if it was used much more it would have ruined the whole housing. I ordered the parts from parts select and to my pleasant surprise they were there in two days. The glides sit right over the door and just slip right in. The felt goes on the bottom under the door and sits in a plastic guide in which the felt is placed I tied the ends of the felt down on the ends with a piece of small wire to make sure they stay in place. It's been two weeks since my repair and there are no problems.
I basically follow the instruction from previous feedbacks. It is very simple just as 1-2-3. The previous instruction are very clear so no need to rewrite them.
First I unplugged the dryer. Then opened the door, removed both screws on top in opening. Then pulled up the top of the dryer and removed two screws, one on each side of dryer and pulled the front off the dryer. I removed the door light from drum bearing housing and pulled off the old drum bearing. I took the new drum bearing, installed the 4 new drum slides onto the drum bearing housing. 2 front dryer drum slides and 2 drum slides. Then snapped it into place and reinstalled the door light. I then vaccumed out the dryer, re-installed the front of the dryer and secured it with one screw on each side, pushed the top back down and screwed in the two screws in the top of the door opening. Job completed, it was fast and the squeek is gone.
pulled the top with 2 screwspulled front with 2 screwscarefull not to pull wiresremoved bad parts not to hardcleaned lint and feltput new parts in reassembledworked goodmake sure you replace all 4 slidesif bearing is cracked replaceand for sure replace felt when you are this farits a cheap repair
This was really easy to me.1. I removed the 2 screws holing the top on.2. Carefully lifted and removed the top cover of the dryer.3. Removed the two screws holding the front of the dryer.4. Pulled the front of the dryer back being careful not to separate the wiring and set it up against the wall.5. Removed the old bearing (which was totally destroyed).6. Cleaned up all the old lint and build up off everything.7. Attached the new bearing after installing the slides.8. Resembled the part by reversing the above process.9. NO more screeching, works perfectly.This cost me a total of $50.00, (I used next day delivery)was completed in 3 days. If I had called my home assurance company it would have cost me $55.00 plus they would have come out, viewed the problem, orders the parts and 10 days later I would have had it fixed. What a waste of my time!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.