Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS6447706
Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Poped the top off took out two screws, pulled the front off removed the old parts and put in the new ones.
Remove plug from wall....very important. Removed control panel, removed two screws holding to on from the front door access. Removed the two screws to the front panel, removed front panel. Removed old front bearing and felt. Install new slides into new bearing and installed felt into lower housing. Vacuumed front panel out and reassembled. Worked perfectly. Thanks to Parts Select, was told 3-5 days for delivery and was here in two. 86 dollars compared to 400 dryer. In this economic market...learn to fix it yourself. With the internet and Parts Select it is easy.
Removed top, removed front to expose front of drum. Replaced bearing with new slides and installed new felt. Cleaned out all the old lint from the exaust chute. This was surprisingly full. Everyone should pay attention here as this could lead to a fire.Overall the repair was easy, parts were correct. One note, order 2 each of the slides, I only ordered 1 each and had to reuse one old one and had to make a new one.
Piece of cake, mostly because of the nice exploded drawing that was on the site when ordering the parts, it was easy to identify what was needed and order it. I will never call a repair man again :-)
First opened cold Bud then pulled screwdriver out of toolbox. Removed all of six screws (quality workmanship of appliance) and put on 6 pieces of plastic (do they make metal any more??????).
First replaced the four drum slides,the lower front felt drum seal and the Drum bearing... Dryer still made LOUD screaching sound.. so I ordered and replaced the Rear drum bearing.And put a new drive belt on it being I had it all apart...Dryer now runs like its brand new.. My Dryer is over 10 years old. Cheaper to fix than replace... As far as Installation goes Was easy...Just watch the repair video or read the other post.. very helpfull...
Took off control panel,top,leftside facing door,and,door panel. Replace the 2 green and 2 white slides, the front drum bearing, the rear bearing and groundind strap behind the heating element,and new belt. Put back together,run's and sounds like new. The hardest part was putting drum bearing in inside and backside of drum by yourself. Replace belt with left side panel off. Easy to get on that way.
I first unplugged the dryer and moved to an open area to work on it. I then removed the three screws that held the access plate to disconnect the drive belt from the motor. Second I removed the two screws that held the top cover on then I removed it and set it aside. Third I removed the control station the thing with all the knobs on it that was about 11 screws (there were a mix of different types of screws some were Hex, Torx and Square tip). Fourth I removed the two screws that held the front door assembly on. I did not need to disconnect any wires to the front door.Fith I removed the Drum assembly by lifting and pressing outward on the outside walls of the frame I then carried the drum and set it on secure surface and then removed the three screws that held the bearing in from the inside. After cleaning the dryer after all components were removed I then removed the heating element that holds the bearing sleeve. I then started putting things back together in reverse order until it came time for the front door upper slide assembly that came off pretty easily it just clipped on I put the white and red sliders on first then I put the whole thing on it just clipped on then I put the front door on and screwed it on and finished putting things back on in reveres order. Then plugged it up and gave it test run and no noise and it runs great I hope for another ten years.
First looked up on Google how to correct the squeak. Almost got into an internet trap by a you tube video looking to seel the slides for $20.00 (white) & $24.00 (green) each but luckily found your website. I originally ordered just the slides (first order) then aferwards ordered everything. Replacement parts fit right in without any struggle.
Order and repair went fine. Just followed installation instructions already posted. However, after the repair it would overheat and shut off. Tested thermostats and they were good. Forums repeatedly talked about air flow problems but I knew it was clean. Ended up putting foam weather stripping on inside of front panel where it meets duct of squirrel fan and that fixed it.
Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.
This was very easy. The utility room is just off the kitchen. I had your repair video running on my laptop on the kitchen island and started at ~8am last Saturday. A very fun project, because all the guesswork has been eliminated by watching your repair video for a few moments, hitting pause, then doing exactly what was explained on the video. I took the time to vacuum out every piece of lint, then carefully reassembled the dryer. One bit of advice- - if you need to disconnect any wires, mark them with a Sharpie pen: one dot on both the wire and the spot you pulled it from, two dots for the second wire, etc. At reassembly time, it's a snap. Also, as you remove screws, keep a few sandwich bags handy so you can group screws together. Have fun!
I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.