| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerChristopher from Winsted CT
Loud squeaking from dryer
Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJeanne from Donora PA
Squeek when dryer was running
removed front door, removed front panel unclipped old drum bearing installed new one installed four new drum slides which were completely worn away. the slides are different two different pairs. i fold out which ones go where from one of i guys on your web site only one of them mentioned two white and two gray where they went. thank you parts came fast fit like a glove dryer is perfect. price was right to.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCarol from Lapeer MI
Plastic & wear strips were worn out & missing
Parts were easy to take out and replace with the new ones.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerjeffrey from adamsville AL
Loud squeaking when dryer was in operation
2 screws, lift the top off and snapped in new drum bearing then added the 4 drum slides and placed top back on dryer, replaced 2 screws. Piece of cake!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMike from White Cloud MI
Dryer sqeaking
remove the 2 screws going into the top, remove it
remove the 2 screws going to the front panel, set it aside install parts and reverse order. very easy to do
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:More than 2 hours
ToolsScrew drivers
CustomerKen from Neenah WI
Sqealing sound during operation
Disassembled and removed drum according to directions on this site. Ordered parts and replaced per instructions - - easy as unscrewing and rescrewing old bearing assembly. Hardest thing was putting the belt on - as I did it fromthe front side and the recommendations are to access from the back kick plate. I did not want to wreck the vent tube so I left the dryer in place and did the entire job from the front.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerROB from CLARKS SUMMIT PA
Loud noise when running
I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerDUANE from Kutztown PA
Loud banging, not drying.
First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDon from Peoria IL
The dryer had a lovely squeak
I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJeffrey from Kelso WA
Loud scraping noise when dryer is running. Also clothing would get stuck around the drum.
First with a screwdriver,I removed the two screws and lifting the top and the front panel of the dyer off. The worn parts were easily removed and the new parts just snapped into place. I then just put the front and top panels back on and the whole job took less than 20 minutes to complete. The next day I received a letter from GE that the warranty would expire and would I like to buy an extention. Thanks to PartsSelect I saved a lot doing it myself.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerRonald from Urbana IL
Noises during cycle
I was actually able to do the repair based on the other repair stories listed on this site. Their instructions were clear and concise which made the job a breeze. The last time I had a repairman come out the bill was $95.00 to disconnect and reconnect a wire. For less than $50.00 I was able to do a much bigger job for a whole lot less. The best part of it all: my wife thinks I'm a genius.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTerry from Brandon MS
Dryer was shaking and vibrating all over the floor
Took top and front panel off. Pulled top bearing shroud off, replaced and installed the slides on new top bearing. Installed felt gasket on the bottom piece of lower shroud. Installed new lamp and put back together to check out. Dryer working great now. Should have changed the belt but it is not squelling so it is fine.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerDave from Ottawa IL
Dry drum was squeeking
Replased drum slide, and wear bearings.
Very easy repair, and the squeeking is gone!!
Thanks for the easy ordering and fast delivery!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerDavid from Lawrenceville GA
Squeaking and black marks on clothes.
Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTodd E from Eaton OH
Makeing a squeaking noise
remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it
todd e line eaton ohio usa
|