Quick Question!

Have you ever purchased from PartSelect.com before?

6447706-1-S-GE-WE1M1067-Drum Bearing Slide - Green
6447706-1-S-GE-WE1M1067-Drum Bearing Slide - Green 6447706-2-S-GE-WE1M1067-Drum Bearing Slide - Green http://www.partselect.com/Schematics/GE/00002276i02.gif

Drum Bearing Slide - Green

PartSelect Number PS6447706

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will Not Start.

Compare At

$5.17

You Save

$.86

Your Price

$4.31
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 140 reviews What's this?
121-135 of 140
 

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Mike from White Cloud, MI

Dryer sqeaking

remove the 2 screws going into the top, remove it
remove the 2 screws going to the front panel, set it aside install parts and reverse order. very easy to do

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: More than 2 hours
Tools: Screw drivers
Customer: Ken from Neenah, WI

Sqealing sound during operation

Disassembled and removed drum according to directions on this site. Ordered parts and replaced per instructions - - easy as unscrewing and rescrewing old bearing assembly. Hardest thing was putting the belt on - as I did it fromthe front side and the recommendations are to access from the back kick plate. I did not want to wreck the vent tube so I left the dryer in place and did the entire job from the front.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: ROB from CLARKS SUMMIT, PA

Loud noise when running

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Drum Bearing Slide - Green
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: DUANE from Kutztown, PA

Loud banging, not drying.

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Don from Peoria, IL

The dryer had a lovely squeak

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jeffrey from Kelso, WA

Loud scraping noise when dryer is running. Also clothing would get stuck around the drum.

First with a screwdriver,I removed the two screws and lifting the top and the front panel of the dyer off. The worn parts were easily removed and the new parts just snapped into place. I then just put the front and top panels back on and the whole job took less than 20 minutes to complete. The next day I received a letter from GE that the warranty would expire and would I like to buy an extention. Thanks to PartsSelect I saved a lot doing it myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Ronald from Urbana, IL

Noises during cycle

I was actually able to do the repair based on the other repair stories listed on this site. Their instructions were clear and concise which made the job a breeze. The last time I had a repairman come out the bill was $95.00 to disconnect and reconnect a wire. For less than $50.00 I was able to do a much bigger job for a whole lot less. The best part of it all: my wife thinks I'm a genius.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Terry from Brandon, MS

Dryer was shaking and vibrating all over the floor

Took top and front panel off. Pulled top bearing shroud off, replaced and installed the slides on new top bearing. Installed felt gasket on the bottom piece of lower shroud. Installed new lamp and put back together to check out. Dryer working great now. Should have changed the belt but it is not squelling so it is fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Dave from Ottawa, IL

Dry drum was squeeking

Replased drum slide, and wear bearings.
Very easy repair, and the squeeking is gone!!

Thanks for the easy ordering and fast delivery!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: David from Lawrenceville, GA

Squeaking and black marks on clothes.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Todd E from Eaton, OH

Makeing a squeaking noise

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Drum Bearing Slide - Green
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Gary from Mount Juliet, TN

Loud grinding noise

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Drum Bearing Slide - Green
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Keli from Manassas, VA

Dryer made hig-pitched screech

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Stephen from CORNWALL, NY

The dryer was squeaking like a recently castrated banshee

I first removed four screws above the door opening to lift off the top, then removed two screws, near the top, inside the front, to remove the front. There I found that 2 grey plastic and one white plastic anti-friction strips were worn to nothing (even the large plastic bezel that incorporates the light was starting to wear away, from just a few days!).

When I went to put the front back on, i couldn't get the lip of the drum to ride properly on the felt. In fiddling with it, the drum fell off the rear bearing, too, so I put it back on.

So I ordered new felt, two white and two grey strips (I didn't know if 1 or 2 were in each $8 "kit"--only one per kit), a spare belt--just in case--and some bulbs.

Putting the strips on was easy--15 seconds each. Putting on the felt took all of 20 seconds. I spent more time scraping off the dust and vacuuming things out!

The drum fit over the felt quite easily now, and when I ran it, it was wonderfully quiet. For a minute! Then, it started making a new, grinding noise!

I had a Sears repairman friend come over, and he found that a small platic bushing had fallen off the rear bearing element. Once he put that in place, it all worked perfectly. Beautifully quiet!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: James from Beaufort, NC

While cleaning dryer for low exhaust discharge pressure, I observed one slide (green) 98% worn down, the other three 90 to 95% worn and felt drum seal broke in half.

Opening the dryer door and removed the two screws located at the top of the opening. Pop off top lid of dryer by lifting up on front, and slide forward. I needed to break it loose by prying it up with a screw driver (use light pressure, be careful not to bend/scrape top), as it was first time every being removed. Remove two screws at top of front panel, hold up drum, and pull front panel forward. Unplug electrical cable to door, and removed front panel. Removed and replaced all four slides (2 Green slides & 2 Clear slides). Removed felt drum seal and replaced by lightly pushing in slots (couple of very light pushes using a screw driver was also needed). Placed front panel back on slots at bottom of dryer (REMEBER TO PLUG IN DOOR SWITCH), lifting (lightly) up on drum, and push in place, replaced all parts in reverse order. Top was a little tricky getting back on, but with a little push it snapped in place. Plugged in dryer performed test run everything worked perfect. Thanks to PartsSelect for their quick response to my order, you are definitely on my favorites listing for any future repairs and/or help.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

121-135 of 140