Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS6447706
Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job
Help other customers find the most helpful instructions.
Were these instructions helpful?
Simple. Followed the well organized instructions on the youtube video and it was done in a jiffy! Saved me hundreds of dollars since I didn't need a repair man and my purchased/replaced parts prevented me from having to buy a new dryer!! Thank you!!
Did repair as per the video except I did not disconnect wires, just swung front panel around. Only complaint...discovered parts were much more expensive than other sites.
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
Mine is actually a twofold thing, bc I diagnosed the problem Bfore taking the dryer apart and looking. Highly recommend taking it apart Before ordering the parts. I started out replacing the belt,bc I had read that it makes most of the noise. While replacing the belt, I noticed the bearing, slides, and felt were all messed up. Still, I felt it would work with just the belt.WRONG! It made it through one load before it broke the belt. Fortunately, I had kept the other belt, and ordered the four other parts. I was able to do it without actually unhooking the door from the housing. I just laid it back against it. No tools were needed to replace any of the new parts. I did get a friend to help me put the old belt (which was still in good shape actually) back on. He has a right arm that works! Oh, forgot to mention. This took less than an hour and I only have my non dominant arm that works due to neck surgery a month ago. Repairing a dryer is easy when you watch the videos. Just don't get intimidated! You can do it!????
I followed the instructions given in the video I watched when ordering the parts. Very easy.
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
Disconnect Power from the DryerRemove 2 screws that held the top on the dryer.Removed the 2 screw that held the front on the dryer.Unsnap bearing from front panel. Snap new bearing in placeand reassemble. Turn power back on.When ordering drum bearing also order 1 set of Front DryerDrum Slides and 1 set of Drum Slides. You need both. Alsoyou should probably check the rear bearing. This would saveyou time and shipping. I didn't and it cost me anothershipping charge as well as a couple of extra days downtime.
2 Screws hold top on, removed top, 2 more screws hold front panel with door on, removed front panel. Unclipped front drum bearing installed new one with new sliders put back together.
Remove top (2 screws) and front (2 screws), snap out old drum bearing, put new slides in new drum bearing and install in dryer. Reinstall front and top of dryer.
The front panel has wear and tear, as was the drum bearing with broken pieces. To buy a new dryer would be several hundred dollars. A repairman told us it is not worth trying to replace the front panel. I found part select and ordered the required parts. All in all my cost is just over 200 dollars and I have a like new dryer. The front panel does not exactly fit my dryer (I guess my dryer is older) so I had to drill two holes to fit the bottom catch plate. I followed the video instructions. It was easy.
Removed two screws to remove top to access drum. Removed two screws to remove front panel. Easily removed drum bearing and snapped in new bearing. 4 Glides were slid into slots. Only one problem. My service parts list called for drum bearing #WE3X37. I was sent #WE3M26. I was assured this was the right part for my dryer. Although the part did fit, I was unable to use the existing light because the the hole on new bearing was too small to accommodate it. Replacement of drum bearing would not be necessary if GE would put visible labels on dryer warning consumers of preventive maintenance of glides that wear.
This took less than 10 minutes to complete. 1) pull off the top of the dryer and remove the two screws that attach the front panel to the side panels. Once you pull the front panel towards you, away from the side panels, you can remove the front bearing. Be sure to be careful not to pull apart the wiring on the left side of the front panel. If you do, it is easy re-attached by hand. The front roller bearing of he drum can be removed by hand. Simply pull upward, with a steady pressure, on the bearing. It will snap out with this gradual pressure. The slide can be inserted by hand, with the two gray slide at 11 and 1 o'clock and the wite slide at 10 and 2 o'clock. The new bearing will snap into place by hand. Carefully insert the light bulb into the hole in the top of the new bearing whle snapping into place. The web site provides a good diagram that illustrates the various pieces and assembly. Once the bearing is in place, lift the dryer drum and set on top of the bearing as you re-attach the front panel to the side panels with the screws removed earlier. Replace the top by snapping back into place. Less than 10 minutes.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.