Freezer Evaporator Fan Motor with Blade

PartSelect Number PS557956

This kit includes the motor and the fan blade. This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Fridge section too warm.
  • Unusual Noise.
  • Compare At

    $72.17
  • You Save

    $12.03
  • Your Price

    $60.14
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Evaporator Fan Blade

Part Number 324817

$19.35
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 4 reviews What's this?
1-4 of 4
 

21 of 25 people found this instruction helpful

Parts Used

  • Freezer Evaporator Fan Motor with Blade

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerKenneth from Mount Kisco NY

Noisy motor bearings

the motor bearing noise/vibration was amplified by the thin metal panel on the freezer's inside back wall. Fridge was making quite a racket. Removed interior shelf, icemaker and rolling tray on bottom of freezer. Shelf and tray pull right out, icemaker is a little trickier but disconnection is not that hard. the plastic piece covering the fan is actually a conduit for airflow from the refrigerator compartment and needs to be removed also. Then, removing the metal back panel reveals the fan and the evaporator coil. The replacement of the fan is very straightforward at this point, couple of screws, couple of wires and thats done. I installed a soft rubber mat cut to size on the inside surface of the back panel with some tape to hold it in place (Used a shower floor non-slip woven rubber type mat - couple of bucks at the grocery store.) Reinstalled panel, duct/cover, tray and shelf. Icemaker was not hooked to water supply anyway so I omitted re-installing that. No more noisy fridge!

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 23 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJOSE from GREENSBURG IN

No cooling in the refrigrator area

first thanks to part select for the info in the web site.last week notice the area in the refrigerator.was bearly cold. went to parts select read the coments.and whala.i am an expert.my wife was amazed.i was sure the evaporator fan not work,but reading in the web site i learn it can be few other parts so a change all 3 parts,just to make sure, thank you again part selact you are the best.and thank you for the magazines.. JOSE ANGEL

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

  • Freezer Evaporator Fan Motor with Blade

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerKathy from LaVergne TN

Freezer was collecting frost and fan motor was noisy

It took about 10 minutes to remove the rear freezer wall from the inside of the freezer area.

Only tool used was a screw driver.

Once the wall was removed, simply removed the old motor and installed the new one.

Replaced freezer wall.

Total repair time was about 45 minutes and easy to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 22 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerKENNETH from METHUEN MA

Refrigerator noisy when fan came on

First I removed the power plug, then 2 screws from bottom panel and removed panel. Removed 2 screws from rear panel and removed 2 screws holding fan in rear panel, disconnected 3 wire leads and inserted them on new fan terminals. Installed screws to hold fan in place on rear panel. Installed rear and bottom panel. Plug in power cord.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4