5574052-1-S-Frigidaire-137513300-Drum Glide - White
5574052-1-S-Frigidaire-137513300-Drum Glide - White 5574052-2-S-Frigidaire-137513300-Drum Glide - White 5574052-3-S-Frigidaire-137513300-Drum Glide - White

Drum Glide - White

PartSelect Number PS5574052

Appliance requires 2 .Sold individually.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Compare At

    $23.45
  • You Save

    $3.91
  • Your Price

    $19.54
In Stock
Order within the next 50 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 20 reviews What's this?
16-20 of 20
 

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerJohn from Edgewater MD

Dryer had loud squeek, barely spun!

First, I shut off the gas & unplugged the dryer. Then I disconnected the vent pipe so I could pull it away from the wall to access the back. Disassembling the dryer was simple.
there are 8 screws: 2 for rear access panel, 2 for top, & 4 for front panel! Once front panel is off, lift back of drum up 2 inches, then forward to get rear bearing out of it's bracket. My rear bearing had worn down so much it was 1/2 the size of the new one! It wore through the bracket down to the metal! I replaced the rear bearing & bracket assembly, as well as the belt & the spring for the belt tensioner! make sure you generously lubricate the new bearing as well as the tensioner pulley! The most time consuming part of this job was cleaning all the lint out the dryer cabinet& cleaning the drum. It works great now! I hope to get a few more years out of it!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

Customerbart from sullivan IL

Glides clicking paper clip in seal

removed top plus control panel laid on back then removed bottom panel and door panel. This made access to drum simple put new glides on and seals back together and running less than an hour.PS dont let little clips fall down in motor area pain to get out,also great time to clean out unit

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customerwilliam from hackettstown NJ

Very loud squeaking

Opened top, removed front cover, removed belt, took out drum, replaced bearing on drum and bearing guide on back of dryer. Reinstalled drum and belt, then replaced drum glides and upper felt,let glue set with clamps over night.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

Customersidney from lockport IL

Drum guide piece broke off causing it to snag drum seal

snapped guide in place and glued seal, I should have purchased 2 seals so they are same thickness2, oh well it is workinf fine .

Help other customers find the most helpful instructions.

Were these instructions helpful?

26 of 680 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Socket set, Wrench set

CustomerBob from Moraga CA

Dryer stopped turning - electrical burning smell

1st, I checked to see if there was anything stopping the drum from turning, that would cause the motor to seize and burn. When that was not the issue, it was evident that the motor was burned out and needed replacement.
2nd, I checked the partselect web site for the parts that would be required to replace the motor, belt, and felt drum guides since I was also getting brown rust stains on the clothes.
3rd, after recognizing that all the parts were in stock and with helpful instructions, I proceeded to take the dryer apart.
4th, unplugged the dryer, removed the cover by removing the 2 back fasteners with a phillips head screwdriver and popped the front of the top off. Remember to slide the grounding wire from the top to the base, found in the back of the top.
5th, I removed the front panel and disconnected the wiring harness. Make sure to mark the connectors so you place it back together the right direction. I placed the front panel aside and also realized the felt strips were brown and the silicon guides were broken, meaning I needed to replace them.
6th, I removed the small back panel near the floor and removed the belt from the idler pulleys and the motor drive shaft.
7th, lifted the drum out of the dryer cabinet by lightly lifting up on the back of the drum to pop the bearing out of the casing on the back of the cabinet. I checked the belt and realized it was cracked and needed replacement. I also noted that the bearing was worn, dirty and needed replacement.
8th, I then popped the spring off the back of the motor bearing, removed the fan housing by removing the 2 screws fastened to the bottom of the cabinet and disconnected the wiring hariness from the motor and the fan. Again, mark the connectors so you know which is up or front when you replace it.
9th, I removed the nut from the fan, recognized the "remove arrow" and used a socket wrench to remove the fan from the motor shaft by turning counter clockwise. there is also a bushing between the fan housing and the motor, and once you get the housing out, you press in the snaps on the side and slide the piece out to release the motor.
10th, I then ordered the parts and cleaned the entire inside of the cabinet, the idler pully's, the exhaust vent, etc. so it was as good as new!
11th, I installed the motor in the fan housing and placed it back in its mount, connected the electric and the front panel and plugged in the cord and turned on the power to make sure the motor worked! Voila!
12th, unplugged the electrical and then proceeded to re-install the fan housing, the drum bearing, pulled off the felt guides, used acetone to remove the adhesive and then added the new, placed the belt on the drum and lifted it back into the cabinet, fed the belt through the pulleys via the back door, connected the power and watched it run!
13th, put the front panel and top back on, connected the vent to the outside and it was all done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-20 of 20