5573867-1-S-Whirlpool-W10509257-Door Gasket - Gray
5573867-1-S-Whirlpool-W10509257-Door Gasket - Gray 5573867-2-S-Whirlpool-W10509257-Door Gasket - Gray http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/OAXZ05N9.gif

Door Gasket - Gray

PartSelect Number PS5573867

It provides a waterproof seal between the tub and the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $54.60
  • You Save

    $9.10
  • Your Price

    $45.50
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 31 reviews What's this?
1-5 of 31
 

118 of 122 people found this instruction helpful

Parts Used

  • Door Gasket - Gray

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerEileen from Salt Lake City, UT

Dishwasher leaking at bottom of door

Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked.
Verified that manifold bearing was not work. It was OK.
Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out.
Dishwasher no longer leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

38 of 42 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerEdward from Springfield, NJ

Door gasket was bad causing a water leak

This repair was very simple. I opened the door of the dishwasher then pulled the old rubber seal (gasket) out; I checked the old gasket to with the new one to ensure the new one was correct then installed the new one. There are two small rubber pieces located in mounting slots below the door gasket that slide out; I slide the old ones out and slide the new ones in. No tools required.
The thing that made the whole job easier was ordering the parts from Parts Select; I couldn't find exactly what I needed on the Whirlpool website but I found exactly what I needed on the Parts Select website and the parts were a perfect match.

Help other customers find the most helpful instructions.

Were these instructions helpful?

35 of 38 people found this instruction helpful

Parts Used

  • Door Gasket - Gray

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerPhil from atascadero, CA

Water was dripping out of the front of the unit down low.

I removed the old gasket, installed the new one which took about 20 seconds.Tested the unit, water was still dripping, but in a different fashion.As per a previous poster's instructions I removed the vent cover. (Located inside the dishwasher up high.)I cleaned out the calcium deposits with hot water and a sacraficial toothbrush. "Ta-Da!" Everything is now groovy!Thank you so very much for your excellent service. Your site was easy to use and your shipping was "lightning fast!" Also, the advice you sent me was invaluable. I thank you, my wife thanks you and my trained lobster thanks you too! :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 18 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerHenry from Raleigh, NC

Dish washer was leaking every once and a while. Shield came out and was deformed by heatinfg eliment and was found on the bottom of the unit.

The gasket was a breeze, with just pulling out the old one and slowly pushing in the new in the track with my fingers. The shield was a little harder since there was no instructions before me. It turns out that it fits in the inner door and is used as a baffel for the steam (another problem with leaking out the bottom). After removing the front cosmetic pannel you need to thread the shield inside on three tabs that hold it. It took a few times to orientate it properly but it snaps in when correct. After the front pannel was put on and the unit test operated, the washer no longer leaks. Highly recommend the parts and help from PartSelect and the others before me.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 14 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set, Wrench (Adjustable)

CustomerJohn from Manchester, CT

Dishwasher rehab

After hearing ominous grinding sounds and water leaking around the gasket, it was about time to rehab the dishwasher. This is usually the point where I say "t'hell with it, buy a new one". I am glad I didn't.
The Kit to rehab the impeller and such had EVERYTHING I needed. Right parts, right price.
Removed the upper arm assembly, T15 screwdriver, the screen strainer, the impeller, T25 screwdriver, the food grinding spring and impeller (the grinding noise, spring was sprung), and finally the post and impeller thingie (had to break it off, very brittle). The pieces went back on a lot more smoothly than it took to get them off!
Use your digital camera! I took pictures of every stage of the parts removal and what I removed. I got confused with some little balls that were inside and the pictures told me exactly where they went.
Door gasket? I should have replaced it YEARS ago, so easy and cheap with PartSelect parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 31