Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS5136129
The gasket provides a seal between the tub and the door. The door strike serves as a mechanical actuator for door switch operation and provides door tension for proper seal.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Had to call and place another order for a special glue that bonds stainless steel to rubber gasket.The special glue part number is:PS382760 Silicone Adhesive $18.82I ordered this special glue (instead of using something like liquid-nails from Home Depot because I had a concern about chemical safety of having a glue that might leech into the dishes during a wash cycle. The install instructions for the gasket (PS3418214 )does not call for having to use a glue to secure the gasket to the dishwasher. The install was really easy because you just push it into the opening all around the front of the dishwasher.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Gasket had a tear in it from utensils in tray moving past the gasket. Pulled off old gasket and pressed new gasket in place. Cut off about 3/4" of excess gasket material with scissors.
Removed old and installed new gasket
I thought the door gasket was leaking. It turns out there is a whole in the tub and I have to get a new dishwasher. I should have looked a little harder into it before I bought anything!
Replaced Door seal
Finding the model number was extremely difficult. Manufacturers who make it so hard to find should be shot! Without any instructions, it took some time to push the gasket into the u shaped flange that holds it. Certainly they could have devised a better system! My hope now is that it will stay and work for an extended time,
It isn't as simple as just pushing the new gasket into the retaining track. It has to be seated correctly by pushng the retainer strip all the way into track inch by inch using a thin blade tool like a butter knife. Very tedious and hard to see if it is seated properly without someone holding a flashlight. I had about 12 inches left to go on the lower left side but a 3 inch long strip of the gasket kept rolling over on its edge as it wasn't seated in far enough, but it was!
Door gasket was applied with the aid of other users descriptions of the process.
Gently pulled the old gasket out. Cleaned up the area with general purpose cleaner. Placed new gasket in place. Very Easy great do it yourself task no repair call required!! Saved $$$$.
Time and heat had deteriorated the door gasket to a point where food was collecting in and around it - I had to remove the old one and clean weekly. Door Gaskets are easy to replace, just pulled out the old one, cleaned out the slot and inserted the new one - Thanks!
Removed the old seal, which was torn in the lower R corner. Simply applied new seal.
Hardest part of replacing the upper arm was removing the top dishwasher rack (pop off clips on the end of the metal runners & slide out). Then it easily snapped together in seconds.The gasket around the inside frame was a tight fit, but pressed in with a kid's plastic spoon (didn't want to cut or damage the rubber). I also scoured and cleaned the door where it seals to the gasket since the old one had left residue which it stuck to. Works like a charm!
I pulled out the old gasket and pushed the new gasket in with my fingers and a little help from a flathead screwdriver. I went in fairly easily and now it doesn't leak. That simple. Thanks.
I removed the old door gasket and cleaned the channel that the gasket sits in. Then I marked the center of the gasket and matched it with the center of the channel. The door latch did get in the way so I had to have another set of hand to get it started. It pretty much went in by hand just by pushing it. There was extra gasket on either side of the bottom of the door. I trimmed to make it fit perfectly. The first time I used the dishwasher it didn't leak. Unfortunately, the second time I did it leaked again. I am going to run it again tomorrow, but does anyone have an idea why it might still be leaking? Thanks
Removed old gasket...started on the right and side and just eased the new one in the slot around the dishwasher. Just guided it in with a screwdriver and butter knife. I was very pleased with the outcome. I know it would have cost much, much more if I had called an appliance repair company. Thank you!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.