http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/DBALC0A5.gif
See part 1 in the diagram

Drain Pump

PartSelect Number PS5136124

Manufacturer Part Number W10536347
Manufactured by Whirlpool

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Will not drain.
  • Unusual Noise.
  • Pumps but will not spin.
  • Compare At

    $133.80
  • You Save

    $22.30
  • Your Price

    $111.50
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 13 reviews What's this?
1-13 of 13
 

94 of 103 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

CustomerROBERT from BARRINGTON IL

Loose change entered drain pump, cracked housing leaked all water out

Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.

At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).

Re-assemble using new pump.

Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

27 of 28 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Socket set

CustomerKerry from Alleyton, tX TX

Water pump for draining

The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring clamps, unhooked the wiring( its a single plug in) and reverse the procedure for installing.

I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.

I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 22 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

Customertom from Vienna VA

Original drain pump housing broke causing leak all over laundry room floor

What a mess!
Unplug the unit, disconnect the hot and cold water supply lines. Remove the drain hose from the wall and slide the unit away from the wall.
It's easier if you lay the unit on it's side, but not required.
Using the flat blade screwdriver, or a 1/4" nut driver, remove the 8 bolts that hold the back cover and lay that aside.
Locate the leaky pump. There are 2. One is the supply pump. One is the waste drain pump and they are not interchangeable.
Using the pliers, slide the spring clamps off of the 2 hoses connected to the pump.
Using a phillips-head screw driver, remove the 3 screws holding the pump to the unit.
Hinge open the cover to the electrical supply for the pump and pull out the connector. It only goes on one way, so reassembly is not an issue.
Throw pump across the street.
Take new pump and reverse instructions above.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 21 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerKevin from Mount Gilead OH

Cracked water pump from change

first flipped washeron its front, took water pump off, put new water pump on and flipped it back upright.
then took basket out of washer to get remaining change out of washer. fairly simple the third time it has to be done,
I also put two short screws into the suction screen of the pump so that no change can reach the pump anymore

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 18 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerKevin from Scribner NE

Water drain pump leaks

This is the second time that I had to replace this pump. The plastic pumps do not handle pocket change very well.Unplug machine,disconnect water lines and discharge flex hose.Tip machine over to front side to gain access to pump.Remove back panel of washer(8 screws). Remove the three screws and hose clamps.Unplug power to pump. Look for coins in pump and in bottom of washer tub.Remove coins if you can.Install new pump and replace back panel.Tip machine back up right.To make sure that I had removed all coins I had to remove stainless steel tub.Use putty knife to release clips that hold the top of washer.These are about 6" in from both sides of front .Push in and lift top away and back.Remove plastic around out side of basket.It just snaps off. Pry off center cap in bottom of basket. Remove nut with socket wrench.It might be pretty snug.Lift out basket. This might be snug also but it will come out.Now you have access to whatever may be entering your pump. I found a quarter and a penny . Remove plastic cover at bottom of tub (2 screws). This is where I found the penny.Good time to clean washer is now. Mine was really scuzzy.Put everything back together and you are good to go.Make sure to check pockets for that loose change,so you don't have to do this a second time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 7 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerShaun from Central Valley NY

Drain pump leaking

Was pretty strait forward. Took the back panel off, removed the 3 mount screws and 2 clamps on the pump, and swapped it all out. Only thing, Paid for 2 day air shipping, took a week for the part to come in. But it was still faster and cheaper then my local parts dealer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerPhil from Bordentown NJ

Would not pump out water

remove back cover plate to access pump replacement of the pump is rather simple the time consumption was because when I examined the pump I found a nickel which wiped out the impeller on the pump after further examination I found other small change in the suction side of the pump unit As a result of this I had to remove the barrel to further clean the reservoir to avoid damaging the new pump.I have repsaired this washer no less than six times over the years.This is a very poorly designed unit for the cost Thank you for the rapid delivery of the part.This wont be the last time I deal your on line service was excellent.Luckily my mechanical experience saved me a ton of money.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Socket set

Customerjon from hannibal NY

Coin in drain pump put a hole in casing

unscrew all the screws on the back of your cabrio washer just the bottom portion to access the drain pump which is located on bottom left underside of the wash drum, the drum on mine is plastic or plastic shroud i guess , theres 3 screws that hold the pump into place, also 2 hose clamps, and the power source, the cap that covers the power source is a bit of a pain to unsnap do this part last cause you'll be able to pull it out from under the drum and get to it easier. once the pump is free just do everything in reverse and you'll be good to go in about 30 to 40 mins . one more thing dont try to caulk or seal on the one thats broke its a lost cause just replace it and make sure like i have been lol no coins left in your pockets before they get washed......whirlpool cabrio other number i got off sticker besides model number is type 580 hope this is helpfull

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerSarah from Olympia WA

Slow leak from a cracked drain pump

I wasn't able to turn the washer on it's side or front, and instead had to prop it slightly up on cinder blocks due to the configuration of my laundry room. The actual repair was fairly simple, had the clamps supplied been easy to manuever, but they were not. The clamp that goes around the hose from the pump into the inlet valve wouldn't go down around the valve where it was supposed to. I had it too far up, so when I ran the washer, the whole hose popped out and flooded my laundry room. My husband suggested a better clamp, the type that actually opens and you can tighten with a screw system. $2.16 at Lowes. 2nd attempt at repair was successful, and so far no leaks. So...save yourself some time and when you get the replacement pump, take those clamps over to Lowes or Home Depot and buy a clamp that you can open fully, slip over the valve, and tighten as much as you need. If I had that type of clamp to begin with, this project would have taken an hour, tops. And by the way, I'm a 36 year old woman with NO experience fixing appliances, but plenty of experience paying other people too much money to fix things that never should have broken in the first place!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerHouston from Ocoee FL

Leaking water pump

The most difficult problem was to identify where the leak was and I tried to repair the old pump but that was a waste of my time. I was most impressed with this company in how fast the order was taken and the perfect part was shipped to me. I received the part in approx. 30 hours after I placed the order. The part was delivered by FedExpress to my front door. A very reasonable price for the part. Anyway, most anyone could have done the repair that I did without difficulty.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJohn from Durango CO

Cracked housing

Turn off and unscrew hot -cold hoses and drain line. Unplug power and pull unit away from wall. Tip onto front of machine and lean it onto something that will give you enough room to work as the pump is on bottom left back of unit. Unscrew all back plate screw's and remove back panel and keep screw's handy. Three main screw's hold pump in place but loosen hose clamp's first and its out. Reverse what you just did and you should be good to go! Good Luck!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerScott from Wyckoff NJ

Water leaking under washer

removed back of washer. turned washer on its side .removed the 3 screws holding pump and the 2 hoses and the electric connection pump came right out. did the reverse to install the new one.stood up the washer and ran it to check for leaks.no leaks installed back of washerand done

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Socket set

CustomerConnie from Woodland CA

A leaking water pump

Have the Maytag washing machine little over2 years and the water pump cracked - very disappointed.
Anyway, removed the back panel, unhooked the hoses, used 5/16 wrench to loosen up the screws, unplugged the power connector than replaced it with a new water pump.

It was an easy repair that I taught my 18 yrs old.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-13 of 13