Electonic Clock Assembly

PartSelect Number PS48856

This digital electonic clock assembly is seven and a half inches long. If you are installing this clock into a wall oven, the metalllic support nut on the center switch is not needed. You will have to remove the nut for control panel clearance. However, if you are installing this clock in your range, do not remove the center nut. This clock assembly comes with an instructions sheet and is used for many ranges and wall ovens.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 4 reviews What's this?
1-4 of 4
 

6 of 7 people found this instruction helpful

Parts Used

  • Electonic Clock Assembly

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerPeter from Savannah GA

Lightening blew out the digital clock works and therefore we couldn't use the self clean oven.

turned off electricity at the circuit breaker.Pulled stove out and looked at the way the control center was attached to the rest of the stove. Removed the knobs and 4 screws and the complete panel could be removed (or pulled out from the oven-wires are still all attached). Then checked with an electric meter to insure the power was off to all the wires. The clock is a self contained unit and all I had to do was to remove 4 screws holding a face plate, replace the unit and reverse the procedure. Only problem I had was getting the screws back into the face plate (I was only able to get 2 threaded-but that will hold for the life of the stove) and put it alll back together. It works wonderfully.

I had a repair company on the phone who said that the service call would be $185 and if I was right about the clock being the problem, that would cost another $345 for the clock and $85 for the return service call to install. I ordered the part from PartSelect .com on Sunday, had it by Thursday and installed that night. My cost was $195 vs approx $600. Why would you do anything else?

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Electonic Clock Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJEFF from ORIENTAL NC

Clock not working--blank

removed 4 screws holding entire face plate. Rolled face plate up on top of stove and left all wires attached (many). removed 4 screws adjacent to clock assy. Removed control knob just on either side of clock assy and removed control screws (2 on each). removed wires attached to clock assy and transferred new assy. Re-assembled and set clock time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsSocket set, Wrench set

CustomerWalter from Harrisville RI

Center post on front panel broke off making use of the timer or clock impossible. Switch on top that operates the downdraft fan and stove light was broken.

Changing the complete front control module would not have been a hard job but the two screws under the left stove knob would not release and the hex wrench stipped the bolt. I was able to undo both right screws on the right knob, releasing the knob control and the right bracket that holds the center control module. Being careful I pried the two left side tabes on the left bracket allowing me to slide the control module
out. I replaced the module and reversed my steps. The top switch that controls the downdraft and oven light was simple. Remove the two screws that holds the bracket housing the switch. Remove the two hold down compression nuts by prying them up. hold broken switch next to new one and attach the four wires. Replace switch, tried to replace the two compression nuts and after a half hour figure out they are too small. Spen another half hour in assorted nut drawer until I found two small nuts and luckily was able to force thread tham on. I can't believe I saved at least $200.00 in labor doing the repair myself. (and the stove works). I'll be doing my own repairs myself from now on. (Okay, within reason)

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Electonic Clock Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerWerner from Radcliff KY

No display, transformer had no output

Removed the 4 screws on the bottom of the panel, lifted the panel out and up to clear the uper part of the panel. Removed the screws from the left and right switches, which hold the bracket of the clock, marked the wires of the clock and removed the wires. Installed the new clock in reverse. The power to the range was off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4