474458-1-S-Frigidaire-5308027429        -High Temperature Adhesive
474458-1-S-Frigidaire-5308027429        -High Temperature Adhesive 474458-2-S-Frigidaire-5308027429        -High Temperature Adhesive

High Temperature Adhesive

PartSelect Number PS474458

Used for installing felt and rubber seals on dryers.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Unusual Noise.
  • Compare At

    $30.28
  • You Save

    $5.05
  • Your Price

    $25.23
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.6 / 5.0, 4 reviews What's this?
1-4 of 4
 

12 of 17 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerChris from Toccoa GA

Drum loose, causing high pitch noise.

First use a vacum to remove all the dust and lint inside the dryer fraim

Some problims removing old rear drum bearing assembly. Also removing old drum guide bottom Adhesive.
I used a new wire brush, but if I had a brush that fit a drill this would have been better to remove the adhesive.

I then applied the Glue, drum seal and small clamps to hold in place so the glue could dry overnight the next day 30 mins and the dryer was back togeather.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers

CustomerGerald from Alliance NE

Burned out heater element

1.Remove 2 screws and the air intake grill on the back of the unit. remove the drive belt. 2. Remove 2 screws on rear of top, slide top back and remove. 3. Remove 2 screws about a foot down on the inside on each side of the front cover. Remove four screws that secure the plastic control panel and the front panel that are right behind the control panel on the top. Disconnect the wiring harnesses, cut the nylon wire tie that is closest to the front cover. 3. lay unit on its back and and remove the two screws on the lower edge of the front panel, take your putty knife and slide it in the gap between the front panel and the dryer cabinet and release the two spring clips on both sides. Then you can lift off the front panel and control panel, set it to the side. 4. Remove the screw and the nylon guide from the center of the top front case crossmember. Remove the three screws on the inside rear of the drum, lift out the drum and set aside. 5. The drum pivot just sits in a nylon socket, pop it toward the top of the machine and lift it out, you may want to clean it good and re-lubricate it on reassembly. Disconnect the wires from the heating element and the heat sensor. 6. Set the cabinet upright and remove the four screws on the back side of the rear of the cabinet but not the two that are right in the center, they hold the pivot fixture and don't need to come out. The heater coil pan is now loose and ready for removal. 7. The seal between the filter housing and the blower housing was torn and this is an important part to have right, any air leak here will do the same thing as a dirty lint filter or plugged dryer exhaust and your new heating element will have a short, hot life. I pulled the old one off, scrapped the old glue off, applied the adhesive like the instructions on the tube say and after a few minutes installed the new seal then set the front panel to the side to let the adhesive dry. 8. The reassembly is just the reverse of the disassembly , use a couple nails or awls to help hold the dryer heater pan in place for screw installation and you might want to gentle squeeze the wire connecters if they feel loose, also check for clogged or kinked exhaust and stress the importance of cleaning the lint filter after EVERY load, it is small and all the air that cools the heating element must go through it, if is isn't maintained your new element won't last long. Have fun!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerTHEODORE from INDIANAPOLIS IN

Dryer would make squealing noise when used

First I removed the top of dryer by prying upwards with a screw driver to pop the clips that hold it in place,the second thing I done was to remove to screws that held the front of dryer in place,these screws are located in side the cover half way down.once tha twas completed I remove the front and took it out side where I used a wire brush to remove the old felt at least what was left.onced cleaned I applied the new felt using the supplied high temp glue and then used clothes pins to clamp the felt in place and left sit over night .next morning I installed with ease and all was fixed. NO MORE NOISE:)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerBrian from Palm Harbor FL

Drum bearing guides worn through - general rebuild

Removed two screws on bottom of front panel. Lifted bottom of front panel, it then it dropped down and was moved to the left side. Removed 4 socket screws and removed drum front cover. Replaced felt strip, removed belt and replaced. Replaced two idler pulleys in back. Removed blower housing front cover, removed blower wheel and replaced. Installed front drum glides after drilling out rivets from the old glides. Vacuumed entire inside thoroughly and reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4