470317-1-S-Frigidaire-5303937139        -Upper Drum Glide
470317-1-S-Frigidaire-5303937139        -Upper Drum Glide 470317-2-S-Frigidaire-5303937139        -Upper Drum Glide 470317-3-S-Frigidaire-5303937139        -Upper Drum Glide http://www.partselect.com/Schematics/Frigidaire/ZHGITR3L.gif

Upper Drum Glide

PartSelect Number PS470317

Front upper felt glide pad with 3 nylon glides - includes adhesive.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Compare At

    $22.45
  • You Save

    $3.74
  • Your Price

    $18.71
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Lower Drum Seal

Part Number 460194

This part helps to keep the dryer running as quietly as possible.

$25.55
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 124 reviews What's this?
26-30 of 124
 

2 of 3 people found this instruction helpful

Parts Used:
  • Upper Drum Glide
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: David from Auburndale, MA

Dryer was snagging clothes between the drum and frame

Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
  • Upper Drum Glide
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Robert from Portsmouth, RI

Dryer squeak during tumbling, worn front drum glide

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Eric from Millbury, MA

Clothes getting stuck and burned

Follwed all the other comments real easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: george from midland, MI

Clothes getting caught on top left of drum leaving brown stains

disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply
front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers
Customer: George from Reno, NV

Loud noise, gringing sound like dry bearings

Took front door off, top off, frunt off, removes screws holding rear bearing pivot, and then removed drum. repainted bearing surface on drum, installed parts, let paint dry for a day and reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

26-30 of 124