Upper Drum Glide

PartSelect Number PS470317

Front upper felt glide pad with 3 nylon glides - includes adhesive.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Unusual Noise.
  • Marks left on clothes.
  • Will not tumble.
  • Compare At

    $23.11
  • You Save

    $3.85
  • Your Price

    $19.26
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Lower Drum Seal

Part Number 460194

This part helps to keep the dryer running as quietly as possible.

$22.80
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 124 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDOUGLAS from CHILLICOTHE OH

Clothes get stuck and burn in upper drum glide

Found the promblem as described at this site while looking for diagrams for the dyer. Repair went as described. Once I removed the old upper drum glide I used acetone to remove old glue. Cleaned up fast and easy. Once installed I let cure for about an hour and then reassembled. Let it cure for about an hour more and then I used the dyer. I could feel that the gap around the front of the drum was again narrow so that my finger tip would not slide into a grove. So far so good.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerEDWARD from DELAVAN WI

Clothes were catching between drum and opening

I followed the video example which very clearly showed how to do the repair. Much easier than I had expected.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set

CustomerSteven from Merrick NY

Washer needed back bearing & drum guides

Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerDEBRA from EL SEGUNDO CA

Clothes were getting stuck and burning in the gap between the dryer and the drum.

Opened up the dryer, scrapped off the old glide and seal. Applied adhesive as instructed. Glued on new seal and glide and reassembled dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerDavid from Coconut Creek FL

The dryer was making a screeching noise sometimes.

I followed the directions from your video, which was a great help. The only difficulty I had was getting the belt in the tension pulley - you can not see what you are doing and the spring is strong - but I got it. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customerjames from charleston SC

Cloths getting stuck between drum and front panel

repaired as described in your instructional video.The video repair part of your website is just great.Seeing it done vs tring to understand someone else describe it makes it that much easier. I will use you for all future repairs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerPaul from Bantam CT

Clothes were getting stuck in crack between drum and front wall of dryer

I ordered parts, recieved in 2 days. came with upper glide, glue and instructions. instructions were easy to read and follow. I used the wood chisel to remove old felt, cleaned well with some solvent, reap[plied glue, wait a few minutes , apply felt - reassemble dryer - viola- done. very satisfied customer

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerJohn from Peekskill NY

Lint got caught up in the bottom and back of the dryer. We then had a small fire in the dryer when the lint caught fire in the chamber.

unplugged the dryer and "popped" the top with a screwdriver. Removed two phillips head screws located towards the top of the drum that hold the front panel in place.Unplug the two wires that attach to the front door switch. Removed the panel. In the center of the drum are three screws that mount it to the rear bearing assy. Thats the part that led to the breakdown of the front seal and guide blocks witch allowed lint to escape into the cabinet. Removed the screws then in the back of the dryer there is a small grill that allows air flow. If you take that off, there is the motor and belt tensioner.. My belt had been ruined so I just slid the drum out the front. Normally you would have to release the belt from the tension pulley and motor first. After sliding the drum out, you see the rear bearing assembly. Behind the flange, there are two screws that have to be removed to get the bearing assy out. Here is the tricky part. The two screws mount into a small plate that is on the back of the dryer. There is a tang in the center of that plate that holds a little steel ball that applies some tension to the bearing to help hold it in the correct position without making it to rigid to move around naturally. when you go to install the new bearing, tape that plate to the back of the dryer to hold it in place while you set the new bearing in place. unless you have someone to hold it, you will drop the ball and you will have to start over again. Using the grease provided grease the socket of the bearing and istall the ball of the flange into it. then take the little ball I described and apply grease to it and stick it to the backside of the bearing socket where you will see a hole drilled out. that ball sits in that hole and rests against the tang of the plate that I spoke of. after that the rest is easy. Remove the top felt piece with the teflon (white ) platwes from the top of the door assy. where the drum rides on. I used a wire brush to clean off the residue of dried glue. use some small pinch clamps or clothes pins to hold the new felt in place. Spread the glue provided onto the now clean surface and wait till it gets tacky ( afew minutes) then lay felt onto it evenly. then use the clamps to hold the felt while it dries. While thats drying, place the new belt over the ring at the back of the dryer. slide the drum in and as you do, pull the belt over the drum and just let it hang there. line up and istall the three screws to hold the drum to the rear bearing flange. then go to the back of the dryer and loop the belt around the motor shaft you will notice that the idler pulley on the tensioner slids right off towards you. Thats so you can get the belt on easier. Slide the pulley off and plce it agaist the belt, pull the tensioner to the right and when you have enough slack, push the idler onto the tensioner shaft. It sounds harder than it is it's really a lot easier when you see it. once the belt is installed remove the clamps from the new felt and install the front panel . place it in at the bottom first taking care to line it up in the grooves then push it into place. there are a couple of alignment clips that will help. Put the two screws in place, plug the switch wires back in, and lower the top. you are done. the only part i left out was to make sure you vacuum the whole thing out while you have it apart. especially where the lint trap is. there is usually a large buildup in there. plug it in and give it a test run.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerJohn from Kirkland WA

Small brown burn like marks on clothes.

The online descriptions were very helpful. I used a wooden kitchen fork to pry open the top of the dryer from the front, about 3 inches in from each side. Two metal springs hold the lid. The wire harness was on the right and two disconnects were easy to separate. Remember to disconnect power before you start. On the inside on the left and right sides are two screws which hold the front on. Remove these screws and the front panel will lean forward. Remember to support the drum as you pull the front off. Remove both top and bottom felt seals. I used a putty knife to aid in the removal of seals. Scrap the residue with the putty knife to remove. Run a bead of glue all around and let set for two minutes. Place top drum guide on first, and center on top. Put lower felt seal on next and tie a rope all around on top of felt, to hold in place while glue dries. Let dry for 30 minutes and remove the rope. Reassembly dryer. Test on low heat. It really is easy to do. Celebrate.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerRay from Boerne TX

The upper drum glide was worn out

I followed the directions that came with the new Drum Glide kit. Unplugged the machine from the wall outlet. Raised the top of the machine which only required releasing the front top clips. Removed the two screws that hold the front cover on. Unplugged the harness connectors to the controls on the front cover. Pulled the front cover loose from the retaining clip and raised it to release the lower part of the front cover. I then removed both the Glide and the lower seal. Had to use Acetone to remove the old adhesive. Used the adhesive that came in the kit to put the new glide and lower basket seal on. I used small clamps to ensure a good fit as the adhesive cured.
Then I put the front cover on raising the drum in the front to allow it to fit into the front cover. The rest was the reverse of what I did to remove the cover. I feel this is an ease repair. The hardest part is cleaning the old adhesive off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrancis from Colesburg IA

Once in a while a piece of clothing would get stuck between the dryer tumbler and the frame around it, it would leave a burn mark on the piece of clothing that got stuck.

I noticed that the dryer drum had some free play and would allow the clothing to get lodged between the drum and the frame around it. I popped the top off the dryer and found that the lining on top of the frame work that carries the drum was woren out. I got on the web and the parts listings and order the part on a thursday and the part was here the next day in the afternoon. I took the old part off and glued the new part on and left it dry over night. the next day I assembled the dryer and it was back in use. The wife was very happy that no more clothing was getting lodge and ruined.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerStephen from Plymouth IN

Dryer kept chewing up zippers and buttons.

Real simple, Unplug power cord from the wall outlet. Then open the top of the dryer by inserting a flat blade screwdriver under the front and pry up till the top snaps open. Lean the top to the back to keep it out of the way. Remove the 2 screws that held the front on and remove the wires for the door switch and the light. Remove the front by letting it lean out about 8 inches and lift it up out of the two bottom clips. Then just lay it any where it will be easy to work on. Clean where the new guide will go. Then just follow the instructions that came with the part. After the adhesive is fully dry just reverse the process and you are done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerTiffany from Jefferson LA

Loud noise ,clothes getting stuck

Removed dryer top. Unscrewed the screw from each side inside the dryer the ones below the control panels. Don't unscrew those you will just have to put them back. Insert a flathead screw driver on the left side to loosen the front panel and slide it gently to the right. You can replace the drum glide without disconnecting any of the wires. Remove old drum glide and clean. Install new one and while the glue dries clean inside the dryer. Mine was very dirty!!!! Put everthing back and your ready to go. Don't forget to hook back the dryer vent. Thank you Partselect my dryer is almost like new and is drying so much faster, no more noise and you have saved me lots of money.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerSteven from Davison MI

Rust marks on clothes during drying cycle.

I'm not very mechanically inclined, but even I thought this was a pretty easy repair. Just pull off the old seal and glide and glue on the new one. I let the glue dry over night, but in reality it probably would have been fine to use the dryer after an hour or so. We've been laundry all day and everything seems tip-top.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerTeresa from Indianapolis IN

Clothes were getting caught in the drum and causing burn marks

The upper glides were worn off and the felt had worn down causing the drum to have a gap at the bottom between the drum and the front panel. Clothes would get caught in this gap.
Removed the top cover and front cover. You do not have to remove the drum to install these parts.
I pulled off the old seals and guides. I used a Dremmel and wire brushed off the old glue. Applied the new glue [supplied with parts] and attached the new seal and guides. While the glue was drying I installed the new belt.
Reinstalled the front panel and the top panel.
Works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?