Upper Drum Glide

PartSelect Number PS470317

Manufacturer Part Number 5303937139
Manufactured by Frigidaire

Front upper felt glide pad with 3 nylon glides - includes adhesive.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Unusual Noise.
  • Marks left on clothes.
  • Will not tumble.
  • Compare At

    $21.98
  • You Save

    $3.66
  • Your Price

    $18.32
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Lower Drum Seal

Part Number 460194

This part helps to keep the dryer running as quietly as possible.

$22.80
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 124 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDavid from Orange Park FL

Dryer drum upper seal worn

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerPlamen from Alexandria VA

Screeching dryer

Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

Tools

CustomerPaula from Somerset MA

Tub rubbing, clother getting stuck and burning

removed old seal and drum glide. sanded off old glue. replaced with new parts, cleaned out the whole bottom of the dryer, runs good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEDWARD from EDISON NJ

Our clothes would get caught in between the drum & the front cover, making marks on the clothes.

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

Customerkevin from knoxville IA

Cloths were getting snagged on top drum guide

Partselect provided me with what to look for with my symptoms and excellent delivery time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerBryon from Springerville AZ

Dryer making groaning, squeking and thumping sound

Moved dryer out where I could get to all sides, then pulled top off, then unscrewed the front panel. The drum lifted out of it's ball bearing assembly in the back with a little force. Then it slid out fairly easy.

I replaced the rear bearing assembly, the bottom drum glide strip, the top drum glide and the vent seal all at the same time. The glue for the glide strips took about an hour to set up and I used clothes pins every 4-6 inches as suggested by someone else here on this site. Then I vaccuumed out the entire dryer body, vent pipes and every nook and cranny.

I put everything back as it had come out and then put the dryer back in it's place. Plugged it back in and it's as quiet as when it was new. Total time of project was about 1:45.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerRonald from Lititz PA

Drum has too much play, scorching clothes.

This is the second time that I have replaced these parts on this unit. The top pops up and then removing two screws holding the front panel on,just pop it off - don't forget to unplug the connector on the top right. Scrape the old drum glide and basket seal off of the front panel making sure you get as much as possible off, clean the surface and re-glue both pieces back onto the panel. The glue set up pretty fast so don't linger. Re-assemble and you're good to go. The hardest part is getting the old glide and seal off - that took about 1 hour of scraping. Make sure you get it clean.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerDavid from Auburndale MA

Dryer was snagging clothes between the drum and frame

Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerROBERT from LAKE ELSINORE CA

Dryer belt broke & would not spin

FIRST I PULLED UP ON TOP PANEL. NEXT I REMOVED THE TWO SCREWS HOLDING ON THE FRONT PANEL ON. NEXT I PULLED FORWARD AND FRONT PANEL PULLS OUT. I CLEANED THE OLD UPPER & LOWER DRUM GLIDE & DRUM SEAL USING A RAZOR BLADE. I USED THE HIGH TEMP GLUE THAT CAME WITH THE TOP GLIDE. I GLUED THEM BOTH ON & LET SIT FOR ABOUT HALF HOUR. WHILE THE GLUED DRIED I INSTALLED NEW BELT & BELT IDLER PULLEY. I RE-ASSEMBLED THE FRONT PANEL WHILE LINING UP THE DRUM. RE-INSTALLED THE 2 SCREWS. SNAPPED THE TOP PANEL BACK IN PLACE. PLUGGED IT BACK IN & TURNED IT ON. AWESOME NOISE WAS GONE & WORKING GREAT.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Upper Drum Glide
  • PLUG

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerTracey from Barbeau MI

Dryer was eating zippers and buttons

Removed the front plate. Scraped off the old felt lining on top of opening. Cleaned, dried and applied glue. Glue is SUPER sticky! Applied felt strip and let sit for 30 mins. The light hole plug just popped in place (2 seconds). My wife held the lid while I scrunched the door back on (tight fit) and we just pushed down on the white tabs that are were attached to the felt to get it to pop back in to place. Wallah! Cheap fix!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

CustomerJack from Phoenix AZ

Drum glide worn out - loud screeching noise.

I popped the top lid of the dryer which has hinges in the rear allowing it to be lifted. This exposes the drum. The front panel then can be detached using a nut driver and phillips screwdriver. The door shut off switch must be then removed so the front panel can be pulled away. I used an adjustable wrench to remove the lock nut. Once the front panel is clear of the drum, the felt and nylon glides are exposed. I removed the felt using a paint scraper, and cleaned the adhesive residue with lacquer thinner. The provided high temperature adhesive was then applied, I waited a minute per the directions, then applied the new felt and glides. The dryer reassembles in reverse of the above disassembly, making sure not to forget to reinstall the door switch. I plugged the dryer back in, and ran a load of laundry in quiet efficiency. Your part arrived quickly, the directions were good, and the dryer now works wonderfully.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerPhillip from Kabetogama MN

Did'nt heat, dryer squealed very loud

I googled and found parts select, listed model make and found parts diagram, found suspected parts from trouble shooting blog. I read repair stories, people who performed identical repairs, followed their lead, made notes ordered parts and
easily repaired my dryer for a fraction of the cost of replacing dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Upper Drum Glide

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

Customerguillermo from los angeles CA

Drum turning out of balance, due to worn out drum glide top and bottom, and clothes being cougth beteween dryer frame and drum

I removed the top lid, then removed the front panel, to expose top and bottom drum glides attached to panel, then using a carpenter shisel, and cutting knive scraped away the old worn out glides, wiped clean with acetone the area were the new glides were being cemented. all of this thanks to couple of customers that had the same issues on their dryer, and documented step by step their own way to have this done, I just followed thru their experiences.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDonald from Monroe MI

Cloths getting stuck between drum and door frame

replaced upper drum gasket(felt) hardest part was removing old gasket(felt) used a wire wheel on a cordless drill and the material came right off job was very easy to complete and got great service from parts select

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsScrew drivers, Wrench set

CustomerRichard from Santa Rosa CA

Clothes got burn marks

After pulling out and unplugging my machine I followed the procedure already worked out by others. I bought and replaced all the parts that were listed as involved with this problem, since I only wanted to do this once and the parts were pretty cheap. The only slightly hard part was reconnecting the drum to the bearing, this could be easier with a third hand.Everything went well and the dryer works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?