470129-1-S-Frigidaire-5303935066        -Flat Style Oven Igniter
470129-1-S-Frigidaire-5303935066        -Flat Style Oven Igniter 470129-2-S-Frigidaire-5303935066        -Flat Style Oven Igniter 470129-3-S-Frigidaire-5303935066        -Flat Style Oven Igniter

Flat Style Oven Igniter

PartSelect Number PS470129

This flat style gas oven igniter has an amperage range between 3.2 to 3.6.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Gas igniter glows but will not light.
  • Little or no heat when baking.
  • Will not start.
  • Gas smell.
  • Oven not heating evenly.
  • Compare At

    $46.50
  • You Save

    $7.75
  • Your Price

    $38.75
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 130 reviews What's this?
121-130 of 130
 

1 of 4 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerChris from Shunk PA

The oven wouldn't light or very slow to light

Removed the two screws, took out the old one and replaced the new one. It was very easy and the oven works great now. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customergerry from dana IN

Oven stopped working

Removed racks. removed two screws in back of bottom shelf of oven.Do not know what type of nut or other fastener was on other end of those screws as they would not tighten when I put them back in. However they are in the holes and the shelf isnt going anywhere.The shelf lifted right out lifting the back up first and sliding out from under lip in front. easy access to igniter use a nut driver for this.In the bottom left corner there was a triangle shape cover that needed removed held by one screw. both wires had clip in style connectors that come right out.Cut these off with plenty of wire to attach to new wires with wire nuts provided with new igniter.Put everything back like the old came off. I used a little electrical tape over wire nuts.Closed oven door and tuned on oven and watched my wife begin to smile as the igniter turned red and oven kicked on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerJoseph from Cleveland OH

Christmas day the oven would not ignite. Had to pull out the camper's folding oven for the cheesy potatoes and cook the chicken over an open fire. We had 10 adults and 5 children (6 and under).

The day after Christmas I searched the net reading various reviews, etc. PartSelect seemed to be the easiest site to navigate and offered How To's notes. Wednesday, less than two days later the oven igniter arrived. This was the third igniter in six years. The grandkids watched me intensly as I read the How to's and easily installed the new igniter. Because of the ease with the website and the fast delivery I am keeping PartSelect.com as part of my resources for the home self doer. The cost was competitive saving me over $100.00 doing it myself. Thank you PartSelect. Joe W Cleveland, Ohio.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerVic from Vista CA

Igniter fail to light the flame

Removed broiling drawer to gain access to the igniter. Remove igniter from mounting bracket, ,cut wires, attach new igniter wiring and reinstall the igniter on the bracket. Reinstall the broiling drawer to complete the job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customerricky from paducah KY

Oven ignited, but didnt get very hot

disconnected the (2) wires of old igniter from (2) wire nuts located under oven in back of bottom drawer, took out (2) mounting screws holding igniter assembly and held it together to new igniter assembly. Stretched out wires together and cut new wires same length as old wires, then mounted new igniter with same (2) screws and connected wires with new included wire nuts and replaced all other oven parts, turned on oven and had a nice TV dinner! :-) Extremely pleased with PartSelect. Ordered part on Tuesday night and had it by Thursday night the week of Christmas no less! Kudos to PartSelect! Great service!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set, Wrench set

CustomerKristy from Smithfield UT

The oven would glow, but not light.

First, I took out the racks. Then I removed the bottom cover of the stove. (This was in place by two screws that I used my drill & socket set.) Next, remove burner cover by a socket set. Finally, in the corner was a metal cover that covered part of the electrical connections. I then used the screw driver to undo the screws that attached the igniter to the oven. I undid one wire connection, and wired it with the new one on the igniter. (To make sure I wired it correctly.) Then I undid the other wire, and connected it with the new wire (using the new wiring nuts provided.) Done! Now just put all the parts back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set, Wrench set

CustomerScott from Colden NY

Stove would glow but not actually ignite, got worse with time

took off door, oven floor and burner cover. cut the wire for the old igniter and used ceramic nuts (provided) to hook up the new one. screwed the new one on with old screws, tested and re-assembled. Saved a hundred bucks easily, but I have some basic electrical back ground.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerJOHN from SOPCHOPPY FL

Oven pilot heater would glow, burner would not light, smell of lp gas

AFTER READING THE INPUT OF OTHERS ON YOUR SITE I ORDERED THE IGNITER. WITHIN A SHORT TIME IT WAS INSTALLED AND THE OVEN WORKS FINE. THANKS FOR THE HELP, JC

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsSocket set

CustomerMichael from Spring Grove IL

Oven would not ignite because the ceramic was cracked off

First i disconected the plug went right where the trouble was.removed the two screws and the safe plate that is protecting the wires.disconeted the two wires and replaced the new ignighter. put everythin back together tried it out ond guess what ??? it works .. Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerDonald from Lone Rock WI

The oven wouldn't heat

Removed the oven racks, and the bottom covers, to get to the igniter. Removed the two screws that hold the igniter in place. Tilted the range forward to get to the wires from underneath, removed the two porclin wire nuts, removed the bad igniter and feed the new wires through wire nutted them. reinstalled the igniter with the two screws. reinstalled the bottom covers.That was it.
With the new drip pans it now looks like a new stove.

Help other customers find the most helpful instructions.

Were these instructions helpful?

121-130 of 130