470125-1-S-Frigidaire-5303935058        -Terminal Block Kit
470125-1-S-Frigidaire-5303935058        -Terminal Block Kit 470125-2-S-Frigidaire-5303935058        -Terminal Block Kit 470125-3-S-Frigidaire-5303935058        -Terminal Block Kit http://www.partselect.com/Schematics/Frigidaire/QKYR9TUK.gif

Terminal Block Kit

PartSelect Number PS470125

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Element will not heat.
  • Will Not Start.
  • Compare At

    $7.15
  • You Save

    $1.19
  • Your Price

    $5.96
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 12 reviews What's this?
1-5 of 12
 

341 of 346 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Steven from Taylors, SC

Rental property stove only had 2 working burners and bottom drawer off track

first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case.
As far as the drawer glides they just snap into place

Help other customers find the most helpful instructions.

Were these instructions helpful?

39 of 44 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: David from Encinitas, CA

Burner shorted out

I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 16 people found this instruction helpful

Parts Used:
  • Terminal Block Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Gary from hollywood, FL

Corroded terminals

was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 19 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Kathy from Lebanon, IN

Burner quit working

pull out old burner, lifted range top change the terminal which took about 5 min. close top put new burner in and was ready to go. works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Gilbert J from HERCULES, CA

To replace the termianl block and the elements

I ordered the correct parts(elements) and PartSelct sent the correct Frigedaire substitute parts.One of the 3 piece metals underneath the element is too long and the element does not fit on top of the bowl of the burner. Frigidaire should make the right substitute parts (elements) for that model.The terminal block took sometime to replace and it works with the old element.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 12