470049-1-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit
470049-1-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit 470049-2-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit 470049-3-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/DBHHKCTB.gif

'M' Series Ignition Coil Kit

PartSelect Number PS470049

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Takes too long to dry.
  • Compare At

    $17.88
  • You Save

    $2.98
  • Your Price

    $14.90
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 34 reviews What's this?
 

5 of 6 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerTyler from Story City, IA

My dryer would light but when it called for more heat it would not light.

lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerAaron from Kerhonkson, NY

Clothes not drying in one cycle

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerJack from Huntingdon, PA

Dryer wasn't heating

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerVincent from Fairfield, CA

Heat would initially come on then go off or sometimes not come on at all.

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

Customerdan from bellingham, WA

Dryer would spin but not heat. The gas flame would only come on once, if that.

Once I found this site, with everybody's description of the problem & fix, it was pretty easy.
Pry the front of the top up using a flat screwdriver at each side. Then disconnected the dryer-controls wire bundle (dryer unplugged of course) at the connector, and unscrewed 1 screw on each side of the front panel close to the top (under the controls, back-side of the panel), in order to pry the front panel off - top 1st.
With everything opened up, just unscrew the two screws on top of the burner coil. the pull off the plate, slip off the 2 coils, disconnect the wires, and install the new coils in reverse. Put it all back together and you're good!
(I replaced the drum glides too, while I was in there - just in time!)

Help other customers find the most helpful instructions.

Were these instructions helpful?