470049-1-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit
470049-1-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit 470049-2-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit 470049-3-S-Frigidaire-5303931775        -'M' Series Ignition Coil Kit http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/DBHHKCTB.gif

'M' Series Ignition Coil Kit

PartSelect Number PS470049

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Takes too long to dry.
  • Compare At

    $17.88
  • You Save

    $2.98
  • Your Price

    $14.90
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 34 reviews What's this?
1-5 of 34
 

62 of 68 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBrett from Monticello, MN

Dryer would heat initially then cool down

The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31 of 34 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBruce from Burnsville, MN

Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.

1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, installed new coils and bracket. Re installed front panel, screws and top.

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 23 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerBarry from Fremont, CA

No heat, but everything else works. Ran continuity tests on everything and found gas valve solenoid coils open.

Just as others described in your forum, getting to the gas valve solenoid coils is relatively easy. Pop the top lid and lay it back, remove 2 inside screws that fasten the front cover and pull back off the snap clips and lift up and off. Remove 3 screws that hold the entire gas control assembly to the bottom of the dryer and remove. Unfasten 2 screws on the valve that lock the plate on top of the two coils, unplug the electrical spade lug connections and remove. Install the new coils and do everything in reverse. Easy as 1-2-3.

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 19 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrancisco from Arvada, CO

Drying times continued to increase over several months until finally dryer wouldn't dry any more.

I did not troubleshoot my gas dryer to find the exact part that needed to be replaced. Instead, I did some research and found that the ignition coils are an extremely common problem.

The top panel of my gas dryer is attached by two snap clips located in the front, about three inches in from each side. I slid a butter knife in the space between the top panel and the front panel to push the clips and release the top panel. Front panel is attached by two screws, one on each side. I removed the front panel to access the heating system on the bottom left of my dryer and immediately saw the two ignition coils with a metal cover on top of them. Removing the metal cover was a little difficult because the two screws holding it in place were stuck. Once the metal cover is off, the two coils simply slide out. On my dryer, the bigger coil had a metal sleeve inside the core. I kept it and used it with my replacement parts.

The most difficult part of the repair was figuring out how to take appart the dryer to access the heating system. Now, the ol' lady is bragging to her friends that I didn't just fix the dryer, but that i've actually made it better than when it was new ;-)

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 14 people found this instruction helpful

Parts Used

  • 'M' Series Ignition Coil Kit

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMichael from Newbury Park, CA

The burner wouldn't ignite

UNPLUG the appliance. After removing the top of the dryer the front is easily removed. To make life simple I disconnected the wire harrness at the quick disconnect and placed the door/front away from the workspace. I removed the bracket holding the coils in place and replaced the old with the new coils. replaced the front and top panels and pugged it in! Good as new!! I originally ordered the wrong part and PART'S SELCET.COM refunded my money no problem! I will bookmark this site and use it again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 34