467699-1-S-Frigidaire-5303323481        -Door Shelf End Cap - Left Side
467699-1-S-Frigidaire-5303323481        -Door Shelf End Cap - Left Side 467699-2-S-Frigidaire-5303323481        -Door Shelf End Cap - Left Side 467699-3-S-Frigidaire-5303323481        -Door Shelf End Cap - Left Side

Door Shelf End Cap - Left Side

PartSelect Number PS467699

This white door shelf end cap is used for left side of some refrigerator door shelves.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

  • Compare At

    $4.04
  • You Save

    $.67
  • Your Price

    $3.37
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Shelf End Cap - Right Side

Part Number 467698

This white door shelf end cap is used for right side of some refrigerator door shelves.

$3.37
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 12 reviews What's this?
1-12 of 12
 

9 of 12 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerChristopher from Salisbury NC

The seals on the doors were shot so the refigerader was sweeting.

I started with the freezer door. I lifted the old gasket from the inside edge to get to the hex head screws that attach the plastic inside liner to the outer door. I did not need to start at any one point so I picked a screw and removed it then I worked my way around the door. I was careful to not drop the liner when I removed the last screw. I removed the liner and pulled the old seal out of its seating grove and replaced it with the new seal. Then I used a hair dryer to fix a few places where the seal was deformed from the packing. The heat helped to get the magnetic seal back into the correct shape. I only had one corner to fix the rest of the seal was fine right out of the box. I applyed a little sealer just as the instruction said to do and then reinstalled the linner and new seal. Then I went through the same process for the refrigerator door. Not a hard job just a lot of screws to remove and then put back. The seal its self took about five minutes. Thanks for the parts!

Chris

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRandy from Page AZ

Supports and end cap were broke (for years)

I removed the broken supports months ago. So, I merely screwed both cover supports into place. The end caps slid into place. Piece of cake. I can't believe you had the parts for our 22 year old refrigerator. You guys are awesome!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerCathy from Bowling Green KY

Door racks bent and broke, could no longer put frozen food in doors

Repair was very simple. I only had to snap the end caps in and fit the door racks over those and snap them in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDinesh from Carol Stream IL

Two of the end caps of one shelf and one of another were broken

Ordered the pairs of end caps for both the door shelves. The parts arrived the next day. Opened the wrapper slid the end caps on and attached the shelves to the door. Bingo!!! It was that Easy! Done in less than two days and less than $20. It took me some time to figure out if the parts were right though when I searched online.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJulie from Hummelstown PA

"someone" snapped the door shelf bracket

I took the door shelf and snapped on the bracket and slid it into place. The inside door bin just slid into place. It took me longer to do a search and find the parts than it did to replace them.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

Tools

CustomerBarbara from Gaylord MI

End caps broken - shelf kept falling off

Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDonald from Spencer IA

Broken shelf clips

snapped in the one end, placed the bar in one end and the other clip on the other end and snapped it in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerChristina from Roy UT

One end cap had broken

I went ahead and replaced all 3 pieces for my freezer door rack because one end piece had broken and during jury-rigging so that I could make it til the parts came I bent the long rod. it was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCarla from Frisco TX

A couple of the endcaps had broken off the bars that are on the freezer and refrigerator door.

First I removed the broken end caps that I had taped on. I then slid the end caps on the ends of the bar and simply snapped them onto the door. Voila!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerJennifer from Cleveland TN

Brokern door shelf end caps

The door shelves in the freezer door of my Frigidaire refrigerator were broken, rendering the shelves useless. I ordered four (4) end caps from PartSelect. The end caps arrived in about five days. I attached the caps to the ends of the door shelves and popped them into the slots on the door. It was a very easy repair!.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerRaymond from Anchorage AK

Freezer drawer rail caps and crisper drawer supports were broken

I removed the old parts, installed the new parts and reassembled the crisper drawer and rails. For less than $50 delivered I was able to bring the unit back to service for our family.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Door Shelf End Cap - Left Side

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRobert from Chicago IL

Unable to use shelf because retaining bar bracket broke.

Cleaned insert hole, did a dry-run, then pressed everything permanently in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-12 of 12