| |
6 of 6 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRandy from Page AZ
Supports and end cap were broke (for years)
I removed the broken supports months ago. So, I merely screwed both cover supports into place. The end caps slid into place. Piece of cake. I can't believe you had the parts for our 22 year old refrigerator. You guys are awesome!
|
6 of 9 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver
CustomerChristopher from Salisbury NC
The seals on the doors were shot so the refigerader was sweeting.
I started with the freezer door. I lifted the old gasket from the inside edge to get to the hex head screws that attach the plastic inside liner to the outer door. I did not need to start at any one point so I picked a screw and removed it then I worked my way around the door. I was careful to not drop the liner when I removed the last screw. I removed the liner and pulled the old seal out of its seating grove and replaced it with the new seal. Then I used a hair dryer to fix a few places where the seal was deformed from the packing. The heat helped to get the magnetic seal back into the correct shape. I only had one corner to fix the rest of the seal was fine right out of the box. I applyed a little sealer just as the instruction said to do and then reinstalled the linner and new seal. Then I went through the same process for the refrigerator door. Not a hard job just a lot of screws to remove and then put back. The seal its self took about five minutes. Thanks for the parts!
Chris
|
3 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCathy from Bowling Green KY
Door racks bent and broke, could no longer put frozen food in doors
Repair was very simple. I only had to snap the end caps in and fit the door racks over those and snap them in.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerSusan M from VIRGINIA BCH VA
Missing freezer door shelf bars
Snapped in missing brackets, cut bar to fit and installed.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDinesh from Carol Stream IL
Two of the end caps of one shelf and one of another were broken
Ordered the pairs of end caps for both the door shelves. The parts arrived the next day. Opened the wrapper slid the end caps on and attached the shelves to the door. Bingo!!! It was that Easy! Done in less than two days and less than $20. It took me some time to figure out if the parts were right though when I searched online.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
Tools
CustomerBarbara from Gaylord MI
End caps broken - shelf kept falling off
Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDonald from Spencer IA
Broken shelf clips
snapped in the one end, placed the bar in one end and the other clip on the other end and snapped it in place.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerChristina from Roy UT
One end cap had broken
I went ahead and replaced all 3 pieces for my freezer door rack because one end piece had broken and during jury-rigging so that I could make it til the parts came I bent the long rod. it was easy.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCarla from Frisco TX
A couple of the endcaps had broken off the bars that are on the freezer and refrigerator door.
First I removed the broken end caps that I had taped on. I then slid the end caps on the ends of the bar and simply snapped them onto the door. Voila!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerJennifer from Cleveland TN
Brokern door shelf end caps
The door shelves in the freezer door of my Frigidaire refrigerator were broken, rendering the shelves useless. I ordered four (4) end caps from PartSelect. The end caps arrived in about five days. I attached the caps to the ends of the door shelves and popped them into the slots on the door. It was a very easy repair!.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerRaymond from Anchorage AK
Freezer drawer rail caps and crisper drawer supports were broken
I removed the old parts, installed the new parts and reassembled the crisper drawer and rails. For less than $50 delivered I was able to bring the unit back to service for our family.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDouglas from Clearwater FL
Broken plastic pieces
I just replaced the broken plastic pieces that I got from PartSelect. It was great and fast.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJulie from Hummelstown PA
"someone" snapped the door shelf bracket
I took the door shelf and snapped on the bracket and slid it into place. The inside door bin just slid into place. It took me longer to do a search and find the parts than it did to replace them.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Door Shelf End Cap - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJim from Decatur GA
Front rack broke off
Slipped out the end caps with the broken prongs from the front rack and slipped in the new end caps. (3 mins.)
|