460194-1-S-Frigidaire-5303283286        -Front Lower Drum Seal
460194-1-S-Frigidaire-5303283286        -Front Lower Drum Seal 460194-2-S-Frigidaire-5303283286        -Front Lower Drum Seal 460194-3-S-Frigidaire-5303283286        -Front Lower Drum Seal

Front Lower Drum Seal

PartSelect Number PS460194

This part helps to keep the dryer running as quietly as possible.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Unusual Noise.
  • Marks left on clothes.
  • Takes too long to dry.
  • Compare At

    $27.36
  • You Save

    $4.56
  • Your Price

    $22.80
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Upper Drum Glide

Part Number 470317

Front upper felt glide pad with 3 nylon glides - includes adhesive.

$20.25
In Stock

High Temperature Adhesive

Part Number 474458

Used for installing felt and rubber seals on dryers.

$25.23
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 64 reviews What's this?
1-15 of 64
 

137 of 205 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerDan from Portland OR

Brown spots on clothing

I was getting brown spots on my clothing since I bought this used dryer. Went to partselect.com Fine with me, but not my wife and daughter! Anyway, after ruling out rust, I ended up here and found Randy's story - without it, I'd be lost! Basically, the felt seal crushes over time, and clothing gets caught in the gap stuck against this nasty old brown felt and leaves a mark.

Replacing the belt was a very good idea, though as mentioned, the drum support bearing is just a "nice to do" - not necessary, but it gives you the excuse to re-grease it (I used a thick Molly impregnated grease from my motorcycle).

The only other advice I can give is that I used a chisel to scrape off the old felt - it came off in very little time, and I didn't end up needing to really do much cleaning of the drum afterwards. Just use a sharp one you're not afraid to dull - it'll be metal-on-metal contact.

Using the spring-loaded clamps that you can get from the hardware store was also a huge help - it just needs to keep the upper glide stuck to the drum for the 30 minutes for the glue to cure - I used 6, but 3 would work. The bottom seal doesn't need them as the felt will tend to stick to the drum when the glue is applied.

You might not NEED to replace the lower seal, but I'd suggest it. It's cheap enough, and this job is "not fun" enough that it only adds a few minutes total - good insurance that you do a complete job.

You also might want to get some aluminum foil tape and re-tape your blower extension tube - mine was ripped off from moving from house to house over the years.

Help other customers find the most helpful instructions.

Were these instructions helpful?

119 of 188 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set, Wrench set

Customerjohn from owego NY

Clothes got caught , burned and ripped on front of drum

I felt ,if I was going to replace the top drum glide and lower basket seal, I might as well replace the belt ,bearing assembly and the idle pulley assembly and avoid having to replace these sooner than later. All of the parts showed alot of wear and the belt like all drive belts, should be changed every 5-6 years.
DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer

Help other customers find the most helpful instructions.

Were these instructions helpful?

26 of 29 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Wrench set

CustomerLeAnne from Anaheim CA

Dryer was leaving marks on the clothes and they were getting stuck in the rim around the door .

Let me start by saying that I am a stay-at-home mommy of 2-year-old twin girls so if I can do this, you can too.
1. I disconntected the dryer from the outlet.
2. Then I had to pop open the top of the dryer. I had to wedge a screwdriver underneath the top lid (towards the front corners) in order to open the top.
3. Looking into the dryer from the top I could see a few screws I needed to remove that were along the sides of the drum. After removing the screws, I was able to remove the front panel of the dryer exposing the drum.
4. The seal that I needed to repair was located on the front panel. I had to remove the old seal (I had to scrap to get some of it removed).
5. I applied the adhesive then attached the upper and lower seals.
6. I let the seals dry for a few minutes then replaced the ront panel. In replacing the panel, the seals need to fit around the drum. You need to be careful in fitting the drum so that the seals remain intact and not pushed out of place.
7. Then, I simply replaced the screws to the front panel and secured the top lid back in place.
FYI: I did have a problem with the lower seal, in placing the drum over the seals, the lower was pushed out of place without me knowing. A few days later, the dryer was making a noise and clothes were still getting caught. After opening the dryer and examining the seal, I needed to reattach the seal. I was out of the adhesive but was able to use Gorilla glue (can withstand any temperature once it is dry). Works good as new now.
FYI: I also have to add that the actual replacing of the seals did not actually take 2 hours but since the dryer was opened, I took advantage and thoroughly cleaned the inside of the dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

23 of 26 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerAnn from Blanco TX

Dryer making squeeking sounds and clothes getting caught in drum causing brown spots

I followed others suggestions with numbered steps and listened to others suggestions about replacing other parts while in the dryer. I took the dryer apart and cleaned it out well. I used acetone to remove the glue from the felt and Drum Glide at the top of the Drum. It worked much better than Goo Gone. By doing the clean up and evaluation one day, I ordered all the parts that I saw were worn or difficult to get to. I replaced the Heating Element only because the old one was very brittle and to get to it again would be difficult. Also, I followed other's advice to photograph the parts before removing. It was easy to remember how things went if I had a photo to refer to.

When the parts arrived it only took about 30 minutes to install them all because the glue removal, lint removal, and parts removal had been done another day. I should add that I am a 66 year old woman and found the job quite simple. Excellent web site. Thanks to others for the step-by-step instructions. Oh, to hold the Drum Glide and felt in place while the glue cured, clothes pins work great. I let the glue cure overnight to make sure that it was really secure.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 17 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerWilliam from Ardmore OK

Dryer was squealing and leaving brown marks on clothes.

Disconnected power and vent then pulled away from wall. You will need to move the dryer away from the wall to replace the ground bearing and retaining plate and/or the dryer belt. Removed top of dryer, disconnected wiring harness' then removed the two screws that hold the front panel on the dryer. After removing the two screws, lift out and then up on the front panel. This should remove it from the retaining clips on the bottom. To remove the dryer belt, remove access panel on rear/ bottom left of dryer. Just inside the panel you will see a tension pulley held by a spring. Use your hands to relieve the tension on the belt and remove the belt from the bottom pulleys. Now go to the side of the dryer and attempt to lift up on the front and back of the drum to remove it from the rear bearing guide. There is a slot that it rides in and it only needs to come up about an inch or so. If you cannot get the the rear bearing free this way, you will have to get inside the drum and remove the three screws in the back of the drum. There are two sets of screws, remove the inside circle of screws. At this point, the drum should slide out the front of the dryer. Use aSharpie to mark the center of the top guide on the metal then use a chisel or putty knife to remove the old guides from the front panel of the dryer. You probably won't be able to remove all of the old glue, but make sure you remove all of the old felt. Lay the panel front down and apply glue to the new top guide. Line up center of top guide with the mark you made earlier. Clamp in place. I used several spring clamps, but clothes pins will work. Now put glue on the bottom guide and clamp it in place. The bevel on the bottom guide will point to the back of the dryer. Now, while your dryer is disassembled and the glue is drying CLEAN IT OUT!!! You'll have no better opportunity to thoroughly clean this thing. Remove old bearing guide from the back of the dryer and replace with the new one. This will include the new grounding bearing and retaining plate. Apply high temp grease (generously) to the new bearing guide. Remove old rear drum bearing from drum and install new one. Take old belt off drum and put new one on. Place drum back in dryer cabinet. Be sure new belt doesn't snag or hang on anything. Guide the new rear drum bearing into the groove on the top of the guide and push down into place. It should be a snap ;-). GO to back of dryer and reinstall new dryer belt around pulleys. I put a little of the high temp grease on the guide pulley shaft on the tensioner. Replace access panel. Reinstall front panel by placing bottom back into the two retaining clips and then use your free hand to lift up the drum and guide it into place around the new guides while pushing the top of the panel into place. Replace top screws in front panel and reconnect wiring harness'. Replace top of dryer, slide dryer into place and reattach vent. Hope thos helps someone. It really wasn't very hard.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerJames from Hanover PA

Clothing getting cought,brown stains,noisey

watch the video first very helpful, was a lot easier than I thought.Dryer was pretty old but I figured what the heck.I replaced front lower basket seal,drum glide,dryer seal,belt,and bearing.Worst part was removing old top and bottom basket seals, a lot of elbow grease.I wouldn't have attempted it if not for the video. Dryer works great thanks partslect I will deffinitly shop here again very pleased, hope to get a few more years out of it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 18 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerDouglas from Cumming GA

Thumping in drum in every revolution

I first watched the video. Had I not done that, I probably would have started looking for a new dryer. The repair is simple and I feel like now I could repair just about anything on the dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 17 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerChris from Toccoa GA

Drum loose, causing high pitch noise.

First use a vacum to remove all the dust and lint inside the dryer fraim

Some problims removing old rear drum bearing assembly. Also removing old drum guide bottom Adhesive.
I used a new wire brush, but if I had a brush that fit a drill this would have been better to remove the adhesive.

I then applied the Glue, drum seal and small clamps to hold in place so the glue could dry overnight the next day 30 mins and the dryer was back togeather.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerDANIEL from WEST HAZLETON PA

Top glide was worn and "grabbing" clothes

Unplug dryer (gotta say it). Remove the two screws that hold in the lint catch. Remove top of dryer (two screws in back hold brackets, the front snaps on). remove two screws along the front edge to take front panel off the dryer (there are also clips). Unhook the two electrical connectors that control the door shut off. Once the front is off, remove the old glide and felt and install the new parts. Be sure not to step on the tube of contact cement, making it explode inside the bag. That sucked. Reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 9 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerJana from Fort Worth TX

Dryer had a bad squeak

Removed dryer front, unscrewed 3 screws in center hub, replaced bearing assembly. Removed old basket seal with razor scraper, cleaned surface with mineral spirits, applied new basket seal. Replaced dryer front and project was done. Dryer has no more sqeaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerKaren from Springfield VA

Squeaks; rusty spots on clothes

1. Released the front latches under the dryer top and flipped it up.
2. Removed two screws holding the dryer front in place and flipped it down.
3. Tore off old drum glide and lower seal.
4. removed most of the remaining fuzz with sandpaper.
5. Glued the new seals in place.
6. Put everything back together.

All in all, about 30 minutes of effort. I managed to come away with only minor cuts and scrapes.

Much cheaper than a new dryer!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerRichard from Pittsford VT

Drum was out of alignment, dryer was eating clothes and zippers

Very simple to take dryer apart ,1st top snaps off and 2 screws and front comes off,Dryer needed new front guide but I replaced rear support and belt also as recommended, good time to clean it out too.Hardest part was getting old guide and lower seal off, don't know if it's right but I used a small die grinder with a wire brush attached and it went real quick to clean old felt and glue off. $85 and dryer runs like it is brand new. easy for anyone with some mechanical ability. PartsSelect webpage made getting the right parts fast and easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMichael from Cumberland RI

Clothing was getting caught between drum and front panel

First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerMichael from Snellville GA

Dryer leaving brown streaks on clothing

Very easy and straight forward repair.

Unplug the dryer and move it to a location that offers some room to work.

Use flathead screw driver to pop the front side top of the dryer up then lift the top of the dryer up to expose the drum.

Use phillips head screw driver to remove the two screws from the access panel on the rear of the dryer. Reach into the access area and remove the drum belt from the tensioner assembly. It's spring loaded so watch your fingers.

Disconnect the wiring harness at the right front of the dryer.

Remove the two screws that secure the front of the dryer to the sides.

Remove the front panel of the dryer by pulling the panel forward then up and off the two tabs at the bottom.

The felt strips and glides (which are worn off if you are doing this repair) are glued to the front panel of the dryer and now need to be removed. Removing the old felt will take some time and is the most difficult part of this whole repair.

Use some goof off or similar solvent adhesive remover to ease the removal of the felt. A putty knife will likely be helpful too.

Once the felt is off, wipe off any excess solvent and make sure the area to be re-felted is clean and dry.

Apply small serpentine bead of provided adhesive to the felt strips and glue the new strips on to the dryer. There is more than enough glue in the tube provided to get the job done. After applying felt strips, let them sit for about 30 minutes before reassembling dryer. You may want to use some light duty clamps to hold the felt in place while the glue sets but that's probably not necessary since the glue sets rapidly. Follow the directions on the glue tube.

Reassemble in opposite order.

Take the opportunity to vacuum out your dryer and give it a good inspection while you have it cracked open. You just might find those socks that disappeared.

Here are some "while your at it" ideas:

Replace both upper and lower felt strips.
Vacuum out entire dryer cabinet and the foam seal on the air box.
Replace drive belt.
Replace light bulb.
Replace bearing ball on rear of drum or apply some lubricant to the bearing.

I'm not saying do all these things, I'm just suggesting these items as things to consider based on the age and usage of your dryer.

This is an easy one person repair that requires no experience or special tools. Don't pay the repair man. Do it yourself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerDavid from Plymouth ME

Worn front drum slides

The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 64