Quick Question!

Have you ever purchased from PartSelect.com before?

459829-1-S-Frigidaire-5303281153        -Rear Drum Bearing Kit
459829-1-S-Frigidaire-5303281153        -Rear Drum Bearing Kit 459829-2-S-Frigidaire-5303281153        -Rear Drum Bearing Kit 459829-3-S-Frigidaire-5303281153        -Rear Drum Bearing Kit http://www.partselect.com/Schematics/Frigidaire/6SLAUZTK.gif

Rear Drum Bearing Kit

PartSelect Number PS459829

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if it is making a lot of noise, it could be an issue with this part. This is a ball-and-socket style bearing. You will need to replace this if the bushing has worn out, or if the ball support is damaged. This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws. Unplug your dryer before you begin this repair.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, KENMORE®, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Marks left on clothes.
  • Will Not Start.
  • No heat or not enough heat.
  • Takes too long to dry.

Compare At

$19.09

You Save

$3.18

Your Price

$15.91
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 105 reviews What's this?
91-105 of 105
 

0 of 1 people found this instruction helpful

Parts Used:
  • Rear Drum Bearing Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Gland from Mount Pocono, PA

The dryer squealed when operating.

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers, Wrench set
Customer: Richard from Lowell, OR

Squeaking screeching groaning

First I removed the top, custom on mine, as it was originally stacked. Then two screws inside near the top come out, and the front was pulled out at the top and lifted off the clips at the base. Best access to the belt tensioner is to remove the air intake panel on the back.

With the belt off the tensioner and motor pulley, the drum can be lifted up and out through the front after removing three screws from the inside that hold the drum to the bearing assembly. The original screws are #2 square/phillips combo, better to reuse than the new phillips only ones if a square drive bit is used.

Then the bearing assembly comes off by removing two screws from the back. For reassembly, there is a steel ball that goes in under the plate in the back. It sits in a hole in the plastic shell of the bearing assembly to help align it. I stuck it in place with grease from the bearing kit, and used my knee to hold the plate over it while holding the bearing assembly with one hand and starting the screws with the other.

The basket seal and drum glide felt were peeled off. Repeated soaking with a citrus based goo remover, scraping with a putty knife, and a little scrubbing with an abrasive plastic pad got the old glue off. A rinse and quick wipe with acetone prepared the surface for the new adhesive. It only needed a minute to get tacky, before the new seal and glide were stuck on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: Steve from LaVernia, TX

Very noisy.

opened top .removed drum then replaced bearing kit.added a new belt .only made sense to do so.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Rear Drum Bearing Kit
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Robert from Millington, TN

Dryer was making loud, constant squeal while running

Followed others directions and it went very well. I could not believe how much lint was packed in the bottom of the dryer! Need to clean this area out perhaps once a year.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Rear Drum Bearing Kit
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Justin from Opelousas, LA

Off balance and noisy operation

removed the drum out the front and replaced

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: James from Farmington, MO

Worn out bearing.

Took out the drum by removing rear bearing and replaced with new one. Replaced top glides at same time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: BRUCE from STANDISH, ME

Squealing (loudly!) rear drum bearing

Parts Select has my high praise! Everything from the ease of the on-line ordering system to the video on how to install the parts (very well done!!) to the quick deliver...all was very impressive. My wife thinks I'm pretty cool that I was able to pull this repair job off and I definitely will come back if I need another part! Thanks for helping this "weekend warrior" shine! Bruce.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers, Socket set, Wrench set
Customer: Paul from McLean, VA

Squeaking drum

Remove the top by using a putty knife and pressing in the tabs on either side. Open front door and remove three screws on inside of drum. Lift drum up and off of the bearing guide/hanger. I removed the motor cover, lower rear left and took a picuture of how it was threaded through the spring pulley system before removing the drum. I replaced the belt while I had the drum out. I also replaced the felt guides while I was in there. There are several good appliance sites out there - I really liked the Appliance guru. Try it out. You will be happy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Chris from Dothan, AL

Bearing had worn and heat element broke

pulled dryer apart removed drum replaced bearing ass. and heat element and then put it back together. works great now. no squealing and heating great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Rear Drum Bearing Kit
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Screw drivers, Socket set
Customer: william from cherry hill, NJ

Rear bearing failure

after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

39 of 174 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Patrick from Humble, TX

Squeeking/ grinding really bad

First I pryed up the top cover then opened the access cover on the rear to remove the belt from the drum. Next I removed the front of the dryer to have access to remove the drum. I then removed the 3 screws that hold the drum to the rear drum bearing assembly and pulled the drum through the front of the dryer. I then removed the bearing and proceded to remove the ground ball and reassembled in reverse steps.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 216 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: Jon from Brooklyn Center, MN

Squeaking, got worse and worse

Printed out what others said, took pictures of everything as I took it apart. I went slow. It all worked the first time I put it back, WOW!
Be careful if you are working with a gas line, use two wrenches to disconnect, less stress on the pipe.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

18 of 356 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: andrew from Waukesha, WI

Terrible shrieking noise and drum stopped moving when under a load

flipped up the top of dryer, turned it 180 so it sat on the washer. next I took out the two screws that held the front panel on. panel popped off and drum came up and then out of bearing assembly. two screws and the bearing assembly came off; it was melted and deformed. The metal on the back of drum was also deformed and worn oblong. then it was back together taking the old piece off watching how it was on the dryer and putting the new one on the same way.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

23 of 650 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: RICHARD from MERCHANTVILLE, NJ

Dryer making noise, discoloring clother and eventually stopped turning

Unplugged dryer. Removed top of dryer. Removed front panel. Remove small access to belt in back panel and note belt configuration thru pullies. Removed plastic guide on front frame, 1 screw. Removed belt. Removed Drum. Lift up drum to release from bearing assembly bracket in back. Small bearing was missing. Removed rear bearing assembly brackets. Removed idler pully assembly, one bolt. Thoroughly vacuum and clean. Scrape off felt on front panel and clean well. Glue on front top of front panel and clamp new felt and guides in place. Replace bearing bracket in rear being careful to replace the small bearing that was missing. I used my laptop to guide me. I had your schematic diagram up on the lap top to make sure I put it back together correctly. Replaced Idler Pully Assemply. 1 bolt.
Unscrew old plate and large ball from back of dryer by unscrewing 3 screws from inside drum. Replace with new part and screws. Put drum back in place and insert in bracket in back. Remove clamps from felt and guides. Put belt in place. Replace palstic guide on front frame one screw. Close front panel. From back access panel thread belt thru pullies. Close back panel. Close top. Allow glue to dry. 2 hours. Test. OK. Allow glue to set 24 hours. Dryer works great. OH yeah. Plug back in..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

26 of 680 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Socket set, Wrench set
Customer: Bob from Moraga, CA

Dryer stopped turning - electrical burning smell

1st, I checked to see if there was anything stopping the drum from turning, that would cause the motor to seize and burn. When that was not the issue, it was evident that the motor was burned out and needed replacement.
2nd, I checked the partselect web site for the parts that would be required to replace the motor, belt, and felt drum guides since I was also getting brown rust stains on the clothes.
3rd, after recognizing that all the parts were in stock and with helpful instructions, I proceeded to take the dryer apart.
4th, unplugged the dryer, removed the cover by removing the 2 back fasteners with a phillips head screwdriver and popped the front of the top off. Remember to slide the grounding wire from the top to the base, found in the back of the top.
5th, I removed the front panel and disconnected the wiring harness. Make sure to mark the connectors so you place it back together the right direction. I placed the front panel aside and also realized the felt strips were brown and the silicon guides were broken, meaning I needed to replace them.
6th, I removed the small back panel near the floor and removed the belt from the idler pulleys and the motor drive shaft.
7th, lifted the drum out of the dryer cabinet by lightly lifting up on the back of the drum to pop the bearing out of the casing on the back of the cabinet. I checked the belt and realized it was cracked and needed replacement. I also noted that the bearing was worn, dirty and needed replacement.
8th, I then popped the spring off the back of the motor bearing, removed the fan housing by removing the 2 screws fastened to the bottom of the cabinet and disconnected the wiring hariness from the motor and the fan. Again, mark the connectors so you know which is up or front when you replace it.
9th, I removed the nut from the fan, recognized the "remove arrow" and used a socket wrench to remove the fan from the motor shaft by turning counter clockwise. there is also a bushing between the fan housing and the motor, and once you get the housing out, you press in the snaps on the side and slide the piece out to release the motor.
10th, I then ordered the parts and cleaned the entire inside of the cabinet, the idler pully's, the exhaust vent, etc. so it was as good as new!
11th, I installed the motor in the fan housing and placed it back in its mount, connected the electric and the front panel and plugged in the cord and turned on the power to make sure the motor worked! Voila!
12th, unplugged the electrical and then proceeded to re-install the fan housing, the drum bearing, pulled off the felt guides, used acetone to remove the adhesive and then added the new, placed the belt on the drum and lifted it back into the cabinet, fed the belt through the pulleys via the back door, connected the power and watched it run!
13th, put the front panel and top back on, connected the vent to the outside and it was all done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

91-105 of 105