459776-1-S-Frigidaire-5303281049        -Front Drum Seal
459776-1-S-Frigidaire-5303281049        -Front Drum Seal 459776-2-S-Frigidaire-5303281049        -Front Drum Seal 459776-3-S-Frigidaire-5303281049        -Front Drum Seal

Front Drum Seal

PartSelect Number PS459776

Used with dryers with a 27-inch drum.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Unusual Noise.
  • Marks left on clothes.
  • Compare At

    $11.23
  • You Save

    $1.87
  • Your Price

    $9.36
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 14 reviews What's this?
1-14 of 14
 

467 of 470 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerMatthew from Portland OR

Clothes getting scorch marks, drum noise

First and foremost, I read the repair reviews here at parts source and found that a) Other people had the same symptoms, b)following their repair tips made it super easy.
What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wide flat belt when in fact I had the smaller ribbed belt. Glad I checked before ordering.
A few things that will make your life easier is once you have the old upper guide/seal removed, put down the glue then use several med sized plastic spring clamps to hold the seal in place while the glue sets up, (@ 20-30 min). Their cheap and you should have some around anyway. When replacing the seals I would go ahead and replace the belt too. It's cheap and if your machine is 5+ yrs old probably is worn. Total cost of repair was about $60 (inc shipping). Took about 1 hr 20 min total time. Most of that time was scrapping the old seal material/ glue off the dryer front. Actual disassembly and repair maybe 1/2 hour. Other little tip is the clips for the lid of dryer is to use a flat screwdriver and gently push straight in until it's compressed enough to release the lid, it will pop up when pushed in far enough. That one took me a while to figure out.
Thanks to Part Select for such a helpful site. My dryer is like new again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

35 of 39 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerRandy from Anchorage AK

Burn/rust marks on clothes

Like many others, i was suffering the problem of rust marks on clothes, which ruins them for good.

We have a Frigidaire Gallery dryer, gas, front loading stacked in top of the washer, which is about 7 or 8 years old.

Turns out the top felt seal was worn out, allowing clothes to get stuck between the drum and the door where they would get the rust colored stain. I think this is fairly common. It also "ate" zippers and buttons.

To open the dryer up, you first want to remove 2 screws at the bottom of the front panel, they are covered by little plastic plugs that pop out. Then, go in through the top- you have to pop the lid up from the front, and it swings up like a car hood. from the top, you have to reach in and undo a screw on each side that holds the front panel to the body of the dryer. it's a little tricky.

After those four screws are removed, the front panel is held on by pressure clips, which you can reach from the top and squeeze so they 'let go'. As those release, the front panel will fall outward with the bottom still attached- there are two small pieces of metal at the bottom that the panel sits in. So you lift the panel straight up to get them off those two guides/hooks, and it's clear.

Next you'll want to shop vac the heck out the whole dryer interior. Mine was caked with dust and lint.

Step two is felt replacement. you have to use some muscle to tear the felt off the top of the door opening, which will leave a bunch of ripped felt stuck to the high temp glue. That's where the wire brush and the Goof Off come in. That stuff worked like a charm to remove every last bit of felt and glue.

Once clean and dry, apply the glue that came with the felt guide, set the felt in place (with those plastic pieces facing up), and hold in place for a while. I used plastic clamps to hold the felt in place for about 30 minutes while the glue set.

For good measure, i also replaced the dryer belt and the plastic ball joint that the drum sits in, but i don't think that was necessary. The belt may be a good idea, and to do that you remove the belt by popping it off the little plastic wheel under the drum first, then it'll be loose and you can remove the belt and put a new one on. (This is also a little tricky, take it one step at a time.)

Then put it back together in reverse order and you'll be done with those rust marks.

(Mine is working great)

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerEdward from Carmel NY

Dryer squeaked

UNPLUGGED DRYER.
1. I used a putty knife to pop the clips in the front. This allows the top to open like a car hood.

2. There are two screws one on each side holding the front to the body. Then there are clips which can just be pulled.

3. There are some electrical connections. I made a diagram and disconnected them.

4. The front slides up off two tabs at the bottom.

5. Peel and scrape off old felt. install new felt using high temp glue and clamps. The top one the plastic guides go to the top.

6. The belt has a tensioner on the bottom right and comes off easily.

7. There are three screws in the middle of the back of the drum. They were very tight and require a good phillips head screw driver.

8. Drum lifts out the front.

9. Unscrew the ball bearing assembly from the back, put the high temp lubricant on the ball.

10. Re-assemble in opposite steps.

Plug in and test.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerBarbara from Rohnert Park CA

My dryer squeaked - the squeak from hell

We had to take off the front door - rather simple. The belt was OK. It simply fit over the drum then was tightened up. The seal supplied didn't want to stick to the door. Thinking it was the wrong one - we went shopping. Come to find out it was the correct seal but the glide has been changed since the inception of my dryer. We had to poke holes in the seal to get the nibs on the glide to fit in the seal. Then it wouldn't stick to the dryer door, so we had to sand the outer door and we put some rtv on it and tied a belt around it to hold it. After drying for a couple of hours, we re-assembled the dryer only to have it overheat and burn up. New dryer $389. sad but true.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Front Drum Seal

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

Customerjeffrey from round lake heights IL

The old drum seal top had torn off.

Opened the drayer top and then removed the front panel.
Removed the bottom seal from the acr as it was warn.
Carefully scarped off the remaining bits of felt from the arc.
Applied the supplied adhesive to the top half of the cleaned arc.
Placed the seal and held in place with small spring clamps.
Let it dry for an hour, then I repeated the process with the bottom seal.
I let it dry over night, overkill probably but I wanted it to stay.
Replaced the front with new seal and closed up the top.
It has been working well since. Thanks for stocking parts that help out homeowner's on tight budgets.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Front Drum Seal

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGordon from Canton PA

Small burn marks on light clothing

First I unpluged the machine, then opened the top with a flat head screw driver. Then I removed the two screws inside, unpluged the door sensor. (makes it stop when opened) Removed old gasket, cleaned with emery cloth, cleaned the residue and applied the glue provided. Waited about 1 min. and applied the new gasket leaving about 1/8'' of it hanging over the door facing the drum.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRyan from Jeffersonville IN

Rust stains on clothes in dryer

1. Slid putty knife under each side of front of dryer to release lid.
2. Removed 2 screws from front of drum to release door assembly.
3. Removed wires from door switch.
3. Cleaned lint out of inside of dryer.
4. Removed old felt seals, upper & lower.
5. Removed old glue with goof off type remover.
6. Glued new seals on & held then in place with clothes pins. (there was enough glue in the tube that came with the upper glide for both seals)
7. Put dryer back together.
**Ensure you verify the correct felt seal pieces with the model number of your dryer, usually on inside of door.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerJeff from Reidsville NC

Clothes where getting brown stripmarks on the fabric.

After removing the front door of the unit I removed the Drum seal felt and upper felt part. Then I cleaned the metal ring with acetone to remove dirt. We you install the new parts the glue sent with the Drum Glide is enough for the task with a little left over. Now its working great.
Thanks for good part Jeff

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerCarlis from Lexa AR

Burn marks on clothes

Opened the top of the dryer (no tools needed).
used socket set and removed the two screws (one on each side). unpluged wires from front panel, labled each (good practice).
Pulled open the front panel.
cleaned old felt off all around the front panel. Wiped down everything. while I had it opened, I vaccumed out the dryer underneath.
used glue provided in felt kit and glued new felt where old was.
let dry, put front panel back on ensuring that the felt was between drum and front panel.
put screws back in front panel. closed top.
Let me say that this is the third time I've done this to this dryer as it is about 18 years old.
Until the heating coils go out, this is the cheapest fix there is. :-)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerROBERT from LAKE ELSINORE CA

Dryer belt broke & would not spin

FIRST I PULLED UP ON TOP PANEL. NEXT I REMOVED THE TWO SCREWS HOLDING ON THE FRONT PANEL ON. NEXT I PULLED FORWARD AND FRONT PANEL PULLS OUT. I CLEANED THE OLD UPPER & LOWER DRUM GLIDE & DRUM SEAL USING A RAZOR BLADE. I USED THE HIGH TEMP GLUE THAT CAME WITH THE TOP GLIDE. I GLUED THEM BOTH ON & LET SIT FOR ABOUT HALF HOUR. WHILE THE GLUED DRIED I INSTALLED NEW BELT & BELT IDLER PULLEY. I RE-ASSEMBLED THE FRONT PANEL WHILE LINING UP THE DRUM. RE-INSTALLED THE 2 SCREWS. SNAPPED THE TOP PANEL BACK IN PLACE. PLUGGED IT BACK IN & TURNED IT ON. AWESOME NOISE WAS GONE & WORKING GREAT.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerRon from New Castle IN

Sqeaking noise

Removed front of dryer scraped old seal off ,used brake cleaner on a rag to get old glue off and roughed up seal area with sand paper ,spread glue on attached seal held in place with clothes pin overnight.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGustavo from Key Biscayne FL

The belt was worn and the clothes were getting stained

I took the front off, placed the belt quite easily.
I then had to unglue the old front drum seal and drum glide and re glue the new one, but it came with everything I needed so there was no problem.
My clothes no longer get these little brown stains they got. I suppose they were getting caught.

Its wonderful!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerAngela from Runnemede NJ

Dryer was putting brown spots and tearing clothes.

My husband took the front panel off. We scaped the old seals off. Used the adhesive that came with the drum glide and replaced both parts. No more ripped and stained clothes, that easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

Customersidney from lockport IL

Drum guide piece broke off causing it to snag drum seal

snapped guide in place and glued seal, I should have purchased 2 seals so they are same thickness2, oh well it is workinf fine .

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-14 of 14