| |
27 of 32 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers, Wrench set
CustomerSteve from Wheelersburg OH
Squeeking like crazy
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
|
14 of 17 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers
CustomerAnn from Blanco TX
Dryer making squeeking sounds and clothes getting caught in drum causing brown spots
I followed others suggestions with numbered steps and listened to others suggestions about replacing other parts while in the dryer. I took the dryer apart and cleaned it out well. I used acetone to remove the glue from the felt and Drum Glide at the top of the Drum. It worked much better than Goo Gone. By doing the clean up and evaluation one day, I ordered all the parts that I saw were worn or difficult to get to. I replaced the Heating Element only because the old one was very brittle and to get to it again would be difficult. Also, I followed other's advice to photograph the parts before removing. It was easy to remember how things went if I had a photo to refer to.
When the parts arrived it only took about 30 minutes to install them all because the glue removal, lint removal, and parts removal had been done another day. I should add that I am a 66 year old woman and found the job quite simple. Excellent web site. Thanks to others for the step-by-step instructions. Oh, to hold the Drum Glide and felt in place while the glue cured, clothes pins work great. I let the glue cure overnight to make sure that it was really secure.
|
13 of 15 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers, Socket set, Wrench set
CustomerGlenn from Fort Worth TX
Dryer squealed loudly
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst.
|
12 of 17 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerJason from Bellevue IA
Dryer was missing the grounding ball and making a loud squeal
First I located the two clips holding the top of the machine on and opened the top of the dryer. I then disconnected the two wires on the door switch and removed the two screws holding the front panel on. After removing the front panel, I vacuumed all the loose lint and as far into the lint trap as possible. I then removed the back vent panel and released the drum belt from the pulley. I pulled the drum out of the support bearing. Then I removed two screws holding the drum support bearing, bracket, and grounding ball clip. I replaced the grounding ball and drum support bearing with new parts, (as the drum support bearing was damaged without the grounding ball). Then I reversed the order and put the dryer back together. Overall I felt the job was easy and I'm happy to be able to use a quiet machine again!!!
|
7 of 12 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:More than 2 hours
ToolsPliers, Screw drivers, Socket set
CustomerIvan from Guaynabo, Puerto Rico AL
Dryer wouldn't heat
First: Remove front and top cover
Second: remove electrical cover assbly
Third: motor belt removed
Fourth: drum assbly and bearing shaft and bracket bearing replaced
Now I need urgently (already ordered) the thermostat and glide drum
|
4 of 5 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers
CustomerDavid from Fairdale KY
Bearing bracket worn out
Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerDavid from Rockville MD
Screeching noise when drying
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.
Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)
Re install everything back again. And you are done
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsScrew drivers
CustomerChad from Reisterstown MD
Loud squeaking c/c unlevel. Led to shaft breaking
Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up.
--The parts were shipped timely,
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerVerlin from Hampton IA
Drum on the dryer quit turning
1) i TOOK A SCREW DRIVER AND POP THE TOP LID UP.
2) TOOK A PHILP SCREW DRIVER AND TOOK 2 SCREWS OUT OF BOTH SIDES OF THE FRONT PANAL.
3) LIFT UP ON THE FRONT PANAL AND TURNED IT OUT TO THE SIDE.
4)PUT THE BELT OVER THE DRUM AND ON TO THE MOTOR AND TENSION PULLEY.
5) PUT EVERYTHING BACK TOGETHER IN REVERSE ORDER STARTING WITH 3 ,2 AND 1
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:More than 2 hours
ToolsPliers, Screw drivers, Socket set
CustomerDouglas Green from Kansas City MO
Dryer bearing failure
From previous responses on this site. I just followed their lead. If I had not found these folks, and the responses, it would have been a nightmare. It looked like and I thought the dryer came apart from the back! But in reality it comes apart from the front!! Absolutely fantastic site and help. Fast shipping, I ordered on Wednesday before Labor Day, didn't expect the parts until the following Wednesday, but received the parts on Saturday morning, and had the dryer back running by Sunday AM. Never even ran out of clean clothes!!!!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
ToolsScrew drivers, Socket set
Customerscott from whitehouse station NJ
Machine was making a squeaking noise.
Followed video instructions that were emailed by you.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:30 - 60 mins
ToolsScrew drivers, Wrench set
CustomerBarbara from Bartow WV
We heard the most deafening screech! When we investigated we found that the plastic part that the shaft rested in was worn, unevenly and the shaft end was scored. (we live in a house with 8 people so a fast fix was needed) I looked up the part on a sears site. When I checked the part avalibility I f
we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerJamison from clayton GA
The drum was out of balance
I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.
|
21 of 674 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
ToolsScrew drivers, Socket set
CustomerPaul from Mont Pelier VT
Rear support bearing squeeking
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket
|
41 of 1283 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers, Socket set
CustomerTimothy from Manlius NY
Retainer around drum dryer was wore, back bearing squeeks
I look up on the internet on how to disassemble dryer to get to the parts needed. Took off top, found screws to take off front. Removed existing drum riding seal and lower seal. Used laquer thinner to remove excess glue. Cleaned throughly with soap and water. Reapplied new seals.
At the same time removed drum and parts in the back of the dryer for ball bearing. great, expeditious help from your store. Thank you
|