Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS457526
Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt.
***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
This is a flat style ridgeless dryer belt.
I unplugged the power cord first of all. Then I pulled the dryer away from the wall so I could get behind it and take off the small vent cover that had two screws holding it. Then I reached in and grabbed the old, broken belt and pulled it out. I reached in and disconnected the idler pulley off of the metal stud that it slid onto and then disconnected the spring off of it. After receiving the new parts I took the new idler pulley and reattached the spring to it and then attached the metal housing to the metal stud where the slot was at. I went to the front of the dryer and took the screws out of the top of the door housing pried the door housing away from the top of the dryer about 8". Also I opened the door of the dryer where I took the new belt and put it around the dryer drum as far as I could get it towards the back. Then I went to the back of the dryer. I put my hand into the vent hole and grabbed ahold of the belt and pulled it all the way towards the back where the old belt used to ride on the dryer drum. Then I pulled all the slack and put the belt over on the pulley that was on the motor. After that I pulled the idler pulley back far enough to position the belt on the pulley and that caused tension on the belt. I then put the vent cover back in place on the back of the dryer and put the two screws in it to hold it. I went around to the front and closed the door on the dryer and put the front housing back into place. After that I put the screws into the top of the front housing. The job was complete so I plugged in the dryer to test it and everything worked fine.
Help other customers find the most helpful instructions.
Were these instructions helpful?
1) Removed rear louvered panel (used nut driver to remove two screws) to access damaged idler pulley. Pulled idler pulley assembly out of the slot of the spacer portion of the idler pulley mounting nut (screws into motor housing) and detached spring. Installation of new idler pulley is reverse of removal.2) Removed door (6 phillps screws). Disassembled door by removing 2 screws that attach front and back plate of door. Reomved old damaged door gasket and installed new door gasket.
Very easy install. Removed the top and front of dryer, and put new belt on drum. Also replaced Idler Pulley (altho didn't really need to.)I've had the dryer more than 20 years, so I am really glad such a simple repair will keep it going!Parts arrived very quickly - great service from PastSelect!
the repair was easy enough, the idler pulley and bracket was 2 screws to access and one bolt to remove. the thing that amazed me was that Parts Select even had the items we needed, the lint trap was trashed for years as well and I'd looked for it a few times but never found it, When we found Parts Select we found every thing the old beast needed. Its much quieter around here now! that sucker used to howl!
I unplugged the dryer. Undid the top by taking out 2 screws and mounts on each side of the back. There were two screws in the front panel that had to be removed. One on each side. Then I took the two wires off the killer switch on the door. Marking which was top and which was bottom. Then I removed the front panel. Then I undid the drum which had 3 screws in. I took out the drum to find the problem. I replaced the drum putting the belt on. Then I took off the back panel at the bottom of the dryer to get at the idler arm. Took off the spring and unhooked the arm. I put the new arm on and replaced the spring. I then put the belt on to the pulley and closed up the back panel. I put back the front panel. I put the top back on. I plugged it back in and turned it on and it worked!
Removed rear inspection plate, removed pulley spring and one hex bolt, replaced in reverse order. Very simple removal and install for this. Glad to see that Part Select still had parts for this 22 year old drier.
I've replaced the rear plastic bearing on this dryer twice, so I am familiar with taking the unit apart. After replacing the bearing in December, the machine still made noise (which had been masked by how loud the bearing was). The belt didn't look so great and it's 13 years old, so I ordered one and a new idler pulley assembly.First, I disconnected the power and pulled it out for access. Using a large blade screwdriver, popped the cover open from the two clips in front. Be sure to support the top cover when you open it on the tabs or they will bend - I propped it against the wall. I disconnected the two wires that go to the door switch, and then removed the two screws that hold the front panel and door in place and lifted/opened that and removed the front panel and set it aside.Next, I removed the back access grill (2 screws) and popped the belt off the idler by relieving the tension on the belt. Using a 10mm socket, I removed the idler pivot bolt and idler arm assembly. I installed the new idler arm assembly in its place and reattached the spring.Moving to the front of the dryer, I lifted the drum off the blower housing on which it was resting and took off the belt through the front of the dryer. I then replaced the belt in reverse. Back through the access panel on the rear, I put the new belt on the motor and idler. Be sure to check that there are no flips in the belt. I rotate the drum by hand a couple of revolutions to be certain.I then reinstalled the front cover and door, reconnected the door switch, replaced the access panel and put the cover back down, popping the clips into place.Put the dryer back in place, reconnected the exhaust and plugged it in. Voila - quiet dryer.As an aside, I also took the time to clean the lint out of the blower and exhaust with a vacuum cleaner hose.
I first removed a vent cover in the back where the idler is located. With pliers I removed the tension off the spring. Next I simply slide the idler off the post. I pulled up on the top panel which opened like a clam shell. I used a flat blade screw driver to separate the front panel from the dryer so I could slide the new belt around the drum. I reversed the steps. All in all it was easy. It took me about 30min including cleanup.
Removed small panel at rear of dryer which allowed access to the Idler Pulley asembly. Easily removed, and replaced with new idler assembly. Fed belt onto new pulley and attached tension spring. Actually, this replacement idler pulley assembly is much better than the original. It has a shoulder to allow the belt to "track" better over drum and around motor pulley. Dryer is now extremely quiet, like a new machine. Hope to get another 29 (yes 29) years out of it. Extremely pleased. Doug East Lansing, Michigan
Removed access door. Disengaged spring, removed old idler. Slipped belt around new idler and motor pulley. Difficulty is putting spring back and inserting idler pulley bracket back in place while there is a lot of tension from the belt. Finally used adjustable wrench as a mini hammer.
First of all, I've purchased a belt from local service center that cost me more than $21 (local tax is 8.5%). But, I can not find the idel pulley assembly so I searched on the Internet and ordered from PartSelect.com.Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster than to get those in local stores (driving .. and hope they have what I want ..).I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley. It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time. Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search. Hope this will help.John
Can't say my husband put the part in while I was at work
Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.Thanks Domenico Intrieri
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.
unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.